Fuse For Progressive Dynamics 9200 Inteli-Power Converter

Question

Question:

For the Progressive Dynamics PD9245C what size fuse do I need on the 12 volt outlet? I am using 2 gauge wire for a 13 foot run to the engine battery.

asked by: STEVE

0

Expert Reply:

You will just need a 30 amp fuse for the Progressive Dynamics 9200 Inteli-Power Converter # PD9245C.

expert reply by: Kyle S

0

Answer 1

To replace your Parallax 7445 converter you can use the Progressive Dynamics 9200 Inteli-Power Converter #PD9245C. This has the same amperage so you can just reuse the wiring running from the converter to the battery bank. The Parallax 7445 should…

view full answer...

Answer 2

Yes you could replace the Progressive Dynamics Inteli-Power Converter part #PD9145A with the part #PD9245C and you'd gain the smart battery charger feature over the standard charger. This is basically a multi-stage charging setup that optimizes…

view full answer...

Answer 3

The Progressive Dynamics PD9200 Series Inteli-Power Converter - 12 Volts - 45 Amps #PD9245C is 8-1/4" long x 7-1/4" wide x 4-11/16" deep. If this fits in the slot you are referring to in the bottom of the power panel then you will be…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Fuse For Progressive Dynamics 9200 Inteli-Power Converter

Continue Researching