Exterior Wall Vent Needed For A Furrion RV Range Hood

Question

Question:

What vent do I need to install this in my RV? I do not have a vent installed today, and the specs say the hole for this vent is only 5-7/8inch whereas the vents that you sell are 10-1/2inch wide.

asked by: Dana

0

Expert Reply:

You're correct that the Furrion Ducted RV Range Hood with Light # FHO23SACRBL rear vent is only 5-7/8" long x 3-1/4" tall, whereas our vents are all larger at 10-1/2" wide x 3-3/4" tall. Typically there will be some insulation in the wall only allowing for a small bit of room for air to escape from the range hood and out the exterior vent. This is pretty typical is a residential setting as well. If you wanted to better control the way if vents you could also use HVAC tape to seal up the space so that the vented air could only flow in one direction.

As for the exterior vents, we currently offer the Ventline Exterior Wall Vent for RV Range Hood # V2111-55 (black) and # V2111-13 (white), which both come with a 1-3/4" collar that can be trimmed down to fit your trailer. I recommend using some butyl tape # AL28FJ on the mounting flange of the vent and some sealant # 344270341437-1 around the outer edge to prevent any water from leaking into the walls of the trailer.

If you find a smaller vent that matches the size of the range hood vent at your local hardware store you can also go that route. Just make sure you properly seal it to the wall so that water can't get in and ruin the wall of the trailer.

expert reply by: Kevin C

0

Answer 1

The duct opening on the back of the Furrion Ducted RV Range Hood with Light #FHO23SACRBP is 10" long x 3-1/4" tall so you would want a vent like the Ventline Exterior Wall Vent for RV Range Hood #V2111-55 ( #V2111-13 for white) or the…

view full answer...

Answer 2

For the Furrion Ducted RV Range Hood with Light #FHO23SACRBL you're going to want to use the Ventline Exterior Wall Vent for RV Range Hood - Locking Damper #V2111-55. This vent will fit in 10-1/2" wide x 3-3/4" tall rough openings and…

view full answer...

Answer 3

Are there steps there currently? If so how many steps are on the assembly and what is the overall width? If you could email me a picture of them that would be helpful as well.

view full answer...

Answer 4

Hello Charles, thanks for reaching out. We do offer a replacement fan blade, the Replacement Fan Blade for Furrion RV 12-Volt Ducted Range Hoods #FR63MR which will fit the 12v Furrion Range Hoods. I am sorry to say that the motor itself is not…

view full answer...

Answer 5

In order for the MORryde StepAbove #MR26RR to fold down you'd need to have between 25 and 29 inches from the threshold to the ground on your RV.

view full answer...

Answer 6

Based on the measurements you provided of your 2019 Keystone Passport 171 EXP you'll need the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways #MR26RR. These steps have an entry height range of 25" - 29" and…

view full answer...

Answer 7

The Furrion Vented Range Hood With Fan, #FHO23SACRBL operates on 12 VDC power. Simply connect to one of the 12 VDC circuits in your campers distribution panel.

view full answer...

Answer 8

From what I could find out about the Lippert 3,500 pound axles, they use the inner bearing #L68149 and outer bearing #L44649, so the Bearing Kit #BK2-100 will be the correct bearing replacement kit for your needs. The included cotter pin and tang…

view full answer...

Answer 9

That is a great question Russ. For your type of situation I prefer to use a hitch like the Equal-i-zer Weight Distribution System #EQ37100ET. This type of hitch does not hang down as low as others like the B&W #BW78FR where ground clearance can…

view full answer...

Exterior Wall Vent Needed For A Furrion RV Range Hood

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching