I spoke with Furrion about the Furrion Range Hood part # FHO23SACRVSS and they informed me that they use Lippert Exterior Wall Vents which we do not offer. That said, it does not matter what brand exterior wall vent you use as they are all pretty much universal. I recommend the Ventline Exterior Wall Vent part # V2111-13 for white or part # V2111-55 black as this will work just fine. The instructions for the Ventline Exterior Wall Vent are as follows:
1: Make sure outside wall surface... view full answer...
The replacement motor for the Greystone RV Range Hood with Light - 12V - 24" Wide - Black Item # 324-000087 is the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood Item # BVD0218-00-R.
If you also need to replace the fan blade the correct replacement is the Replacement Fan Blade for Ventline RV Range Hoods - 7" Diameter Item # BVD0216-00
view full answer...
The Ventline Pinnacle Ductless RV Range Hood # VE26SR is exactly what you're looking for. This range hood is black in color and has a 12V fan, 20" wide, and an overall depth of 12". This range hood is also available in stainless steel # VE58SR, and black with stainless steel trim # VE98SR.
All these range hoods feature bright LED lights to illuminate your countertops and have a simple 2 wire design for simple installation. view full answer...
According to the video for the Furrion # FHO23SACRSS, the depth from the front edge to the back is 16-5/8" then there is a 1" collar that would normally fit into wall opening for the outside vent. So 17-5/8" if you count that. The measurement across the front is 23-1/2" wide, and the height at the back is 4-3/4". I have attached a link to the video below.
Keep in mind that most range hoods extend beyond the cabinet several inches to better draw off the front range burners, so this would... view full answer...
The dimensions that the Ventline Range Hood # S0721-24GC-F-1 normally uses for the wall opening is 10-1/2 by 3-3/4 inches. Most RV range vents would be set up for this but in case you need a damper to go along with the range we have the part # V2111-13. view full answer...
While we do not have RV range hoods that are designed to vent through a microwave, there are still options available to you.
If you are concerned with having to cut a hole in your trailer, then you can use something like the Furrion Range Hood - 12V - Ventless, part # FHO23SACRVBL. This vent does not need a duct (the whole that the air flows through to the outside). Instead, it disperses the air coming through the vent back out of it after filtering it. Meaning, smoke and other dirty... view full answer...
Yes the Furrion Vented Range Hood w/ 12V Fan # FHO23SACRSS that you referenced will work great with the Furrion Damper # V2111-13 that you referenced as well. view full answer...
The Furrion Range Hood part # FHO23SACRVBL which is a ductless unit won't be as efficient as a ducted unit but considering a ducted unit would require a much more involved install, it's worth going with the ductless unit if you don't already have the ducts run from a previous one. I can't really say I see many trailer owner's running the duct work for a ducted unit as the process is just too involved. The ductless units still work well with the integrated filters as they absorb a lot of... view full answer...
I would be happy to help you find a 12" deep range hood. I am not sure whether you want a 20" wide or 22" wide hood so I found both. These range hoods are efficient, and the single-speed fan pulls air through the filter and vents it out. The aluminum mesh grease filter is removable for easy cleaning. These are the same model hoods with the exact same function. The only difference is the width.
20"- Ventline Pinnacle Ductless RV Range Hood with Light - 12V - 20" Wide - Black
Item #... view full answer...
The Ventline S0721 Series RV Range Hood part # S0721-20BD-F-1 for black or part # S0721-20WD-F-1 for white is just what you are looking for. The portion of the vent (flange) that mounts to the bottom of the cabinet is 12" deep which is the least we offer so it should be a perfect fit. It comes with a 12 volt motor and light, although incandescent. For reference, the width is 20". In regards to height, this is listed as 5-1/2" tall. Please note, you will need to run a vent to the exterior... view full answer...
The Furrion Vented Range Hood With Fan, # FHO23SACRBL operates on 12 VDC power. Simply connect to one of the 12 VDC circuits in your campers distribution panel. view full answer...
The only part we carry for the Greystone Euro Style RV Range Hood # 324-000089 is the 12V Push Button - On/Off
switch which is part # 37213985. view full answer...
I went to the warehouse and measured the Ventline S0721 Series RV Range Hood, part # S0721-22GC-F-1.
I have attached a photo of the range hood with the measurements shown you can check out. The overall depth of the range hood is 18 inches. The 12-inches is just for the part of the hood that has the fan as noted in the photo. This range hood measures 22 inches wide and has a height of 5-inches.
It sounds like the # S0721-22GC-F-1 would be the range hood you need based on the dimensions... view full answer...
The green/yellow wire you're seeing on your Greystone RV Range Hood with Light - 12V - 20" Wide - Black # 324-000085 is just a ground wire. You leave it or run it to a ground screw at your nearest junction box. view full answer...
The microwave in the photo looks like a Greystone Standard RV Microwave w/ Trim Kit - 1,350 Watts - 0.9 Cu Ft - Black # 324-000105.
And Yes the Furrion Standard RV Microwave - 1,350 Watts - 0.9 Cu Ft - Black # FMSN09BL can be mounted over the range. view full answer...
I went to our warehouse to get the Ventline part # S0721-20GC-F-1 to provide you the exact size and location of the outside vent. I also measured the grease filter too. See diagram to the right as well as the video attached.
The location of the outside vent is on the backside top edge of the range hood # S0721-20GC-F-1. The overall width is 20-inches wheras the outside vent opening is 9-5/8 inches long and 3-3/8 inches in height.
If you are looking at the backside of the range hood... view full answer...
Your Rangehood would have a 1 year warranty. Are you sure the ground wire is connected to a sufficient ground? If you verified you have power to the switch, which is new, and you replaced the motor the only thing left to check on your Ventline S0721 Series RV Range Hood # S0721-20BD-F-1 would be the ground. view full answer...
As long as you're ok with there being some dead space either in front of, or behind it, then there is no reason you can't install the Ventline Pinnacle Ductless RV Range Hood with Light - 12V - 20" Wide - Black # VE26SR in a 15 inch deep cabinet space. 12 inches is the minimum amount of space required. view full answer...
I wasn't able to find any info on your range hood but we may have a solution but you'll need to measure your current range hood to see what would work. We have options that are 20 inches wide like the part # 324-000085, 22 inches wide like part # S0721-22WD-F-1, and 24 inches wide like part # 324-000087. Best option will be to compare what you have to these and see which would fit best. view full answer...
The closest vent hood we have that has the 12 inch depth would be the Ventline S0721 part # S0721-24BD-F-1 which is 24 inches wide and 12 inches deep. Furrion does not make a similar one in this size but the Ventline models do work really great.
I attached an install/review video for this for you to check out as well. view full answer...
The Ventline S0721 Series RV Range Hood w/ Light - 12V Fan - No Damper - 12x24 - Smooth White # S0721-24WD-F-1 utilizes the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood # BVD0218-00-R which has specs of 12v and 5 amps maximum. That translates to 60 watts max.
The Replacement #921 Lamp Bulb for Ventline RV Range Hood # VA0415-00 pulls 18 watts. view full answer...
I took a look at the installation instructions for the Greystone Range Hood part # 324-000086 which are included with the unit for you and they do not specify the routing for the exhaust vent. This part of the install process, the duct work will be up to the user to decide. For an exterior vent you can use the Ventline Exterior Wall Vent for RV Range Hood part # V2111-55. view full answer...
The Greystone Euro Style Range Hood part # 324-000089 with the glass removed has a face plate that measures about 15" x 15" which I confirmed myself. In regards to installation, as long as you secure the face plate and find a way to exhaust the 6" diameter conduit I don't see any issues not using all the aluminium shielding. view full answer...
An electronic resistor is not part of the S0721 series of Ventline RV Range Hoods such as # S0721-20BD-F-1. If there is power to the motor but it has stopped working I recommend replacing the motor with the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood # BVD0218-00-R. view full answer...
It sounds like you are looking for a new range hood for your RV. If that is the case then we have several options for you. In order to choose the correct replacement I would need to know the size of the unit you have now. We currently have options for 20", 22", and 24" wide ranges. I have attached these options for you below. They all have a light and 12 volt fan and they are available in white, black, and stainless.
20" Wide x 12" Deep:
Black- part # S0721-20BD-F-1
White- part #... view full answer...
The white wires of the Ventline S0721 Series RV Range Hood # S0721-20BD-F-1 that you referenced are ground wires. If yours isn't connected most likely either the light or the fan won't work. You'll want to secure that wire to a suitable ground and you'll be good. view full answer...
I wish I was able to provide you with this information but I spoke with our contact at Greystone and they do not have that information available for the Greystone Range Hood # 324-000087; they do not test those types of specifications on their products. From what I was able to find out from some people in the industry, most range hoods that are available for RVs are going to be capable of around 100 CFM (which is pretty standard).
view full answer...
I spoke to my contact at Ventline and they informed me that the Ventline S0721 Series RV Range Hood part # S0721-22GC-F-1 has a 12 volt 100 CFM fan. view full answer...
For the Ventline Range Hood part # S0721-20BD-F-1 that you referenced we do have a replacement fan motor with the part # BVD0218-00-R. And then for a replacement light bulb you'd want the # VA0415-00 and you'd be set. view full answer...
For a Replacement Damper for a Ventline P-Series Range Hood with a horizontal vent we offer part # BCA0472-00 which also fits B and T series vents. Please refer to the linked photo that shows each of these Ventline vent styles. I went to our warehouse and measured this item myself. Note the damper measures 9-3/8- x 4-3/8 inches. The tip-to-tip measurement at the two tabs is 10-1/4-inches. Since this replacement part fits multiple products it might differ slightly from your vent's original... view full answer...
If this is in reference to the Greystone Range Hood part # 324-000087, it sounds like you may have the wires for the motor reversed or some other wiring issue which is then causing the fan to push air out of the screen rather than pull air through. I have attached for you the wiring diagram of the unit which you will need to review to be sure yours is installed correctly. If the fan blade was installed backwards that could also be causing this issue but I am not sure if that is possible.
If... view full answer...
The motor for the Ventline S0721 Series RV Range Hood w/ Light and 12V Fan # S0721-20WD-F-1 is part # BVD0218-00 and has an output of 1.2 amps. There is also a small light, part # VA0415-00, with this range hood which is rated for 16.8 Watts and draws 1.4 amps.
So the motor and the light combined will draw 2.6 amps. view full answer...
The thermal fuse you have found is not present in any of the materials the company provides or is known by their techs. You can bypass it without issue as it isn't needed. If the motor functions when you bypass it you are good to go. If not, then the motor has gone bad in your Ventline S0721 Series RV Range Hood # S0721-20BD-F-1 and simply needs to be replaced. You will want the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood # BVD0218-00-R you referenced. view full answer...
The only reference to the second part number you mentioned I was able to find online was on an Australian auction site but judging from the appearance of the unit in pictures it appears to be the exact same thing as the Furrion Vented Range Hood # FHO23SACRBL that you referenced.
I attached a review video for these for you to check out as well. view full answer...
The Greystone Range Hood - 20" - Stainless Steel # 324-000086 does not have a reverse on the fan. The manufacturer may have attached the wires to the motor backwards which would cause that issue. Swapping the wires to the motor will change the direction the motor spins, and change the fan blade rotation, so that is my recommendation to fix your issue. view full answer...
I attached a link to a page that has all of the stainless steel range hoods we offer for RV applications like the # S0721-24GC-F-1 that you referenced. For example, we have the Furrion Range Hood # FHO23SACRVSS that is stainless and has a 100 cfm fan with a charcoal filter built into it. There's a review video for this vent attached to this page as well.
It's dimensions are 23-1/2" long x 4-3/4" tall x 17-3/4" deep. view full answer...
The Ventline S0721 Series RV Range Hood part # S0721-24GC-F-1 has a 100 cubic feet per minute (CFM) rating which is standard across all of our range hoods. view full answer...
Essentially the two Ventline S0721 RV Range Hoods you mentioned are the exact same but the part # S0721-20BC-F-1 approved for use in Canada as it meets CSA standards and the # S0721-20BD-F-1 does not have this certification. view full answer...
The Ventline range hood, part # S0721-20BD-F-1, is designed to pull air from the RV and vent it outside. If yours is running in the opposite direction it sounds like you may have the wires reversed which would cause the fan to go in the opposite direction.
The black wire is positive and the white wire is negative. On the motor the black wire should be on the side with the red mark. view full answer...
If you had a way to direct the air flow of the Greystone Range Hood part # 324-000085 above the hood you certainly could using duct work, but there isn't a way to orientate the current vent on the hood to push out air through the top of it. view full answer...
I spoke with my contact at Ventline who said that the CFM rating for the Ventline S0721 Series RV Range Hood w/ Light - 12V Fan # S0721-20BC-F-1 is 100. She said that they don't have a Sone rating for it though.
Attached is a review video of the range hood for you to check out. view full answer...
The Greystone Euro Style Range Hood # 324-000089 comes with duct work that was intended to connect to an outside vent. If you didn't connect the duct work to a vent it would not be recommended to run the vent otherwise it would basically just recycle the vented air back into the camper. view full answer...
The Greystone # 324-000087 RV Range Hood is 24 inches wide and vents directly horizontally to the rear, through the RV sidewall. The Ventline S0721 Series comes in various widths, and from what I've seen they all vent out the back. If you have a 24 inch available space above your cook top and the Ventilne hood you have vents to the rear, the # 324-000087 would work perfectly for you.
I've linked to a product Description video featuring the Greystone RV Vent Hood you mentioned. view full answer...
The replacement motor for the range hood part # S0721-24GC-F-1 that you referenced is the part # BVD0218-00C. I can't recommend this motor as a fit for the Heng range hood. view full answer...
If you fast forward to the 3:10 mark of the video I attached you get to hear exactly how loud the Ventline Range Hoods are like the part # S0721-24GC-F-1 that you referenced. It will be about as loud as an oscillating fan that you would have in a bedroom. view full answer...
The Ventline S0721 Series RV Range Hood that you referenced, part # S0721-20BD-F-1, has an actual weight of approximately 7-1/2-lbs (shipping weight including packaging is 9-lbs). Please note this range hood does NOT have a damper and does require a separate dampered exterior wall vent like # V2111-03 (this plastic vent has an actual weight of just a few ounces).
For just about any size or brand of range hood we offer the packaging materials in which we ship the unit will weigh between... view full answer...
The Ventline S0721 Series RV Range Hood w/ Light # S0721-24GC-F-1 that you referenced does not have a damper so you would want to get a hood that has one if a damper is desired. For one with a 1-3/4 inch collar you would want the # V2111-13, for a 5/8 inch collar you would want the part # V2111-03.
Both of these vents have locking dampers. view full answer...
Since your wall thickness is 1-3/8 inches the damper you'll want is the deeper part # V2111-13 which is 1-3/4 inches. This will allow you to trim it back as needed so that it fits properly with the Ventline S0721 Series RV Range Hood # S0721-20BD-F-1. view full answer...
Some range hoods recirculate air through a charcoal filter, but the Greystone Euro Style Range Hood # 324-000089 vents air outside and does not recirculate. view full answer...
Ventline exterior wall vent # V2111-55 has the same measurements as the white version # V2111-13 so either one will work with Range Hood # S0721-20BD-F-1. view full answer...
The Furrion Range Hood # FHO23SACRVBL referenced in your question is designed to hook up to a 12V DC setup so the only way you would be able to use it with a 110V/120V AC system is by way of a converter like the Go Power # 34266169. This will convert your AC shore power to DC power so you can run the Furrion Range Hood or other 12V accessories.
We do have one range hood available that is designed to run off 110V power and it is the Greystone Euro Style # 324-000089. This certainly has... view full answer...
The only range hood we offer that vents out the top is the Greystone Euro Style RV Range Hood w/ Adjustable Shroud # 324-000089 which is designed for 110v power, and you will need make sure there is at least 24" clearance between the cabinets for this range hood to fit. The Greystone # 324-000089 has a very modern look, and shroud enclosing the vent is adjustable to fit your RV setup.
I included a picture of the Greystone # 324-000089 installed in a customers RV for you to take a look at. view full answer...
The Greystone Euro Style RV Range Hood # 324-000089 is designed to be powered by 110 volt AC power like what your house has ran through it so it can easily be made to work in your house. view full answer...
I would love to help but unfortunately Greystone was not able to provide me with the CFM or the sones rating of the Greystone Euro Style Range Hood part # 324-000089. They just don't test for these sorts of things. However, I called Ventline who also makes range hoods and they were able to give me a 100 CFM rating of the Ventline S0721 Series RV Range Hood w/ Light part # S0721-20GC-F-1 but not a sones rating. With that being said I would assume that Greystone would be similar to the Ventline... view full answer...
Ventline S0721 Series RV Range Hood # S0721-24BD-F-1 measures 24-inches wide and it requires a cabinet depth of 12-inches (meaning 6-inches of the hood's 18-inch total depth extends forward of the cabinet surface). If your cabinets are 18-inches deep this means that the entire depth of the hood will be under the cabinet when installed. This should not pose any issues.
Please feel free to let me know the side-to-side and front-to-back dimensions of your mounting location in the trailer... view full answer...
The RV range hoods that I have played with had the guts easily accessible by completely removing the hood from where they were mounted.
The fan blade should just pull off. The shaft that it attaches to on the motor will probably have a D shape (but not always). If it does then there is only one way it can go back on.
The motors are usually attached with fasteners at the top of the motor so having the range hood completely out is going to make things a lot easier. Take a look at the... view full answer...
The Ventline Pinnacle RV Range Hood with Light - 12V - 22" Wide - Black # VE78SR is just for 12V DC, not AC. You could use a converter such as Go Power RV Converter and Smart Battery Charger - 12V - 55 Amp # 34266169 to convert AC to DC and run this range hood if you indeed have AC power only.
view full answer...
The Ventline S0721 Series RV Range Hood w/ Light - 12V Fan - 12x20 - Stainless - Canada Approved # S0721-20GC-F-1 will likely work as a replacement so long as you have the required dimensions, but it is not designed specifically as a replacement for any model of range hood, including a Hengs.
All the Ventline requires is that you have a 20" wide opening and 12" cabinet depth and it uses an 8" x 8" grease filter.
I have added a link to a video review with more info on the range hood... view full answer...
We don't sell them, but you will need a converter to take the 120 volt power source and convert it to 12 volts to do this. Once you have one you could easily install the Ventline S0721 Series RV Range Hood w/ Light # S0721-24WD-F-1. view full answer...
The Ventline S0721 Series RV Range Hood w/ Light - 12V Fan - 12x20 # S0721-20GC-F-1 under cabinet height is 5-1/2 inches tall overall and has a 3/4 inch drop. I've attached a photo to assist. view full answer...
The Ventline Pinnacle Ducted RV Range Hood with Light # VE38SR does not come with an exterior vent so you would need to purchase one like the Ventline Exterior Wall Vent for RV Range Hood # V2111-55 separately. view full answer...
Installing a range hood like the part # S0721-20GC-F-1 wouldn't be hard. It has mounting brackets that would attach it to the kitchen of your trailer right above oven. You can attach it to the bottom of cabinets or a microwave. You would need to use an exterior wall vent like the part # V2111-13 as well. You would not need to have a vent route that goes from the hood all the way to the exterior of the trailer.
You would just need to use the vent cover for the hole you cut so that moisture... view full answer...
To replace your 20" white vent hood we will only carry the following vent hoods.
Black w/ Stainless Steel Ventline Pinnacle Ductless RV Range Hood with Light # VE58SR
Black Ventline Pinnacle Ductless RV Range Hood with Light # VE26SR
Black w/ Stainless Steel Ventline Pinnacle Ducted RV Range Hood with Light # VE98SR
Black Ventline Pinnacle Ducted RV Range Hood with Light # VE38SR
view full answer...
Although the Ventline S0721 Series RV Range Hood with Light, # S0721-22WD-F-1, was designed to be mounted under a 22 inch wide x 12 inch deep cabinet, as long as your alternate mounting surface is strong enough to hold the vent you shouldn't have any problems.
Since this will be a custom installation, you will have to determine the best way to route the vent through the sidewall of your trailer and where to access the electrical to power the fan.
This vent will require the use of... view full answer...
We have the Ventline S0721 # S0721-24GC-F-1 which is a damperless or ductless design that measures 12 inch by 24 inch which should work well for you. This is a stainless steel unit that I attached a review video for down below for you to check out as well. view full answer...
The filter is on the bottom of the Ventline S0721 Series RV Range Hood part # S0721-24WD-F-1 so it is super easy to replace and does not require you to remove anything to access it. If you take a look at the attached review video you will see what I mean. The correct replacement filter is the Replacement Grease Filter for Ventline RV Range Hoods part # BCC0246-00. view full answer...
The Ventline # S0721-24GC-F-1 range hood features a single speed motor. The hood features two switches, one for the light and the other for the fan. I checked out Ventline's catalog, and didn't see that they had a dual speed fan available.
The hood doesn't have a damper, you'd need to use a # V2111-03 exterior wall vent that has a damper. view full answer...
We don't carry any range hoods over 24 inches wide. The 42 inch width is more of a home range hood size. Unfortunately the residential ones will not have the 12V van. The best option I can give is to give you 2 units to fit that 42 inch by 12 inch inset.
For that application, I recommend the Ventline S0721 Series RV Range Hood w/ Light - 12V Fan - 12x20 - Stainless # S0721-20GC-F-1 and the 12x22 # S0721-22GC-F-1. view full answer...
The lifted sides like you see on the Ventline S0721 Series RV Range Hood w/ Light - 12V Fan # S0721-22BD-F-1 gives you a gap that in some cases is used to simply allow the wiring connection for the fan and light. It does in some instances require adding some wood to the underside of your cabinet to allow for a clean look and proper installation depth for the mounting holes. view full answer...
My contact at Ventline confirmed that the correct replacement fan/light switch for your PR-8 model kitchen range hood is no longer available. My contact indicated this kitchen range hood used a dual rotary control knob for both light and fan functions.
It is sometimes possible to find an alternate part at a hardware/electrical supply store but it may be easier to just replace the whole hood assembly with a new unit. I have linked for you our page for complete range hood assemblies which... view full answer...
Many times vent filters will have some indication of which way the air flow goes through it so look on the filter for some indication of that. It could be an arrow or possibly even the words TOP or FRONT. I don't know that the filter in the vent actually has this. Based on what I could find out about the filter, # BCC0246-00, it shouldn't matter.
I went out to the warehouse and pulled a whole vent assembly that uses the same filter. I removed the filter and found that there are some... view full answer...
The stainless version you are looking for is part # S0721-24GC-F-1. The height at the rear of the assembly is 5 inches not including the railing on the outsides. view full answer...
The Ventline RV Range Hood # S0721-24GC-F-1 measures 12 x 24-inches. This and all other sizes and models of RV range hood are shown on the linked page. The smallest available size is 12 x 20-inches. That item in stainless steel is part # S0721-20GC-F-1. view full answer...
Since the Greystone Euro Style RV Range Hood # 324-000089 has a 6 inch duct you'd need a 6 inch to 4 inch duct reducer to fit this to a 4 inch duct. We don't offer this but they are easily available at local hardware stores to you. view full answer...
We do have a variety of range hoods that you can choose from. The Ventline S0721 Series RV Range Hood # S0721-20BD-F-1 is a popular choice on our site. It comes in smooth black and has a light and 12V fan. I have attached a review video of this range hood as well as a link to our selection of range hoods for you to check out. view full answer...
You are correct that the range hood replacement you need is determined by the size so you just need to take some measurements. For example the Ventline S0721 Series RV Range Hood # S0721-24WD-F-1 is 24 inches wide and it does come with wiring. You simply need to disconnect your old range hood's wiring and connect the wires on this one.
I have added a link to a video review I highly recommend checking out as well as a link to our selection of range hoods. view full answer...
The Ventline S0721 Series RV Range Hood w/ Light - 12V Fan part # S0721-20GC-F-1 is your best option for a range hood if your last hood melted. It includes a 12V fan to dissipate the heat and vent exhaust fumes through the trailer's wall compared to other hoods that just use air filters which allows the hood to overheat. The whole range hood is stainless steel except for the fan but can easily be wiped down. view full answer...
Unfortunately, we do not have the Ventline Pinnacle Ducted RV Range Hood with Light - 12V - 20" Wide - Black w/ Stainless Steel, part # VE98SR, in any color other than black.
I have included a video demo link below. view full answer...
Go To Results