Which Over Under Kit Fits Dexter 6k Trailer Axles

Question

Question:

My 5th wheel has two dexter axles #4015551 6000 pounds capacity. Will the K71-385-00 Dexter Axle Over/Under Conversion Kit work on my 5th wheel? Also I have two axles so i would need to order two kits correct? Thank you

asked by: Greg H

0

Expert Reply:

A 6k Dexter axle like what you have has a 3 inch diameter so the Over Under kit part # K71-385-00 that you referenced is correct and would work. You would need to order a quantity of two of these since it is a tandem axle trailer.

expert reply by: Jameson C

0

Answer 1

Welding is usually not required for the Lippert Ground Control 3.0 Leveling System, #LC358590. The taller front jacks will replace your existing landing gear legs that should be mounted to the trailer to brackets with a bolt. and the smaller rear…

view full answer...

Answer 2

I have an axle that is pretty close to what you're wanting, but is not going to work as the spring center measurement is a bit off and it needs to be just right to work. I do have a solution though. You can get the Timbren Axle-less Trailer…

view full answer...

Answer 3

While we currently do not have the Nova style of slam latches we do offer a more generic looking style with the Global Link RV Baggage Door Slam Latch with Keyed Alike Option #295-000015 along with the backing plate #295-000016. This slam latch…

view full answer...

Answer 4

For a replacement pin for the Curt Friction Sway Control part #17200 you can use our part number #55515. This would be a step up from what came with your kit as it has two indentions that the pin would have to overcome to fall off unlike what came…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Which Over Under Kit Fits Dexter 6k Trailer Axles

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching