Are Replacement Bolts Available for the Curt Cargo Carrier?

Question

Question:

I love my hitch and cargo thingy. My question is: The holes that the supplied bolts are to screw in were so rusted that one bolt broke when I tried to get it on. Do you sell Plusnuts that would accomodate the bolts? I will need to drill out the rusty ones first.

asked by: Jeff P

0

Expert Reply:

The 24x60 Curt Cargo Carrier for 2" Hitches # C18152 does not have replacement hardware available but it just uses 3 M12 x 75mm hex bolts which you can find in any local hardware store.

Since you're needing to also drill out the hole, you'd need to use a 1/2" bit # PTW8589. This will make the hole slightly larger since metric and imperial aren't 1:1, but its close enough to not be super noticeable.

expert reply by: Bryce D

0

Ben S.

11/14/2025

Bryce: Wonderful info! What about the smaller screws that attach the bracket to the two sides?

Jesse M.

11/17/2025

@BenS Are you referring to the smaller bolts for the two connecting plates? Those are M10 x 20mm carriage bolts.

Answer 1

As far as I know this is not a common problem, and not something that we have had reported as an issue for the #FA94-00-1000. It is important to make sure that everything is secure when installing the weight distribution hitch. The spring bars should…

view full answer...

Answer 2

The cargo bag I highly recommend for your Pro Series Cargo Carrier #63153 is the etrailer Cargo Bag #988501. It has 20 cubic feet of storage, is waterproof with PVC coated nylon, and has six tie-down straps that will secure it to your Pro Series…

view full answer...

Answer 3

Hello Erald, Thanks for writing in Yes, you are on the right track with the Roadmaster Dual Hitch Receiver Adapter #RM83SR and the Flint Hill Goods Cargo Carrier #FHG87ZR. The #RM83SR is made for exactly what you are wanting to do. You can put your…

view full answer...

Answer 4

Hey Michael, welcome back! The Benton MoveHitch 60x24 Cargo Carrier for 2" Hitches #B38VR you looked at does have a tilt away feature. This can help with loading/unloading, and also help clear a rear hatch. The tilt mechanism is one of the…

view full answer...

Answer 5

Hi Darren! We are here to help! ^___^ So in your case, absolutely do not trust AI. It's basically just taking what will kind of work for most people and applying it to your situation. However, your situation is much more unique than the typical…

view full answer...

Answer 6

I do have a solution for you, but the 24x60 etrailer Cargo Carrier #e98874 is not designed to be used on the back of an RV. Generally speaking, folding carriers are not ideal because they do not stand up too well to the extra stress exerted by the…

view full answer...

Answer 7

Hey David! The Curt Cargo Bag #C18211 can be used with the 22x60 Flint Hill Goods Cargo Carrier #FHG49ZR. However, the bag itself is 22" wide, while the cargo carrier has an inside width of 20-1/2". You will be able to sit it down inside…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hello Stacy, thanks for reaching out. As far as the Draw-Tite hitch for the 2025 BMW X1, the #76018 is the correct choice. The 76923 is only for the 2016-2023 model so that would not be correct. The #76018 on the other hand is confirmed to fit the…

view full answer...

Are Replacement Bolts Available for the Curt Cargo Carrier?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching