Availability of Replacement Power Gear Motor 1010000143

Question

Question:

Power gear electric jacks p/n 1010000143, break kit and what ever else I may need , they dont hold after the coach levels

asked by: Tracy C

0

Expert Reply:

The part number 1010000143 you mentioned cross references with the Power Gear part # LC386198 which is the left hand side replacement. The matching right hand side is the part # LC89CJ.

expert reply by: Jameson C

0

Answer 1

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 2

I spoke with Advent and they said the only fix is to use the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners #ACRG15. This will remove the Coleman from the equation allowing for the advent upper unit to communicate…

view full answer...

Answer 3

I reached out to my contact at Lippert and he said that it sounds like you have an older Power Gear Manual Leveling kit that had the ground running from the solenoid to the control board. This new kit, part #LC359259, can be used as a replacement but…

view full answer...

Answer 4

The Power Gear Motor 1010000155 has direct replacements of Replacement Motor for Lippert Power Gear Electric Leveling Jack System part #LC386198 or part #LC89CJ. These can actually be used on either side. I reached out to Lippert and they said to…

view full answer...

Answer 5

I do have a solution for you, but since the Power Gear 500457 and 500456 are obsolete you will need to replace the controller and keypad. To do this you'll need the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259. This will…

view full answer...

Answer 6

Per the manufacturer when it comes to the shear pins being broken you would have to replace the whole Lippert Jack #LC298707 because the shear pins are not replaceable, and there is no way to fix them. What you will need to do is purchase a whole new…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of Replacement Power Gear Motor 1010000143

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching