Replacement Leveling System Module and Key Pad for Power Gear Part #500457

Question

Question:

controller is obsolete so I need fix

asked by: Gregg T

0

Expert Reply:

I do have a solution for you, but since the Power Gear 500457 and 500456 are obsolete you will need to replace the controller and keypad. To do this you'll need the Replacement Lippert Power Gear Manual Leveling Control Kit # LC359259. This will get your system back up and running while also upgrading it to the current design.

expert reply by: Erik B

0

Answer 1

I reached out to my contact at Lippert and he said that both the Keypad 500456 and the 500457 module are obsolete but the Replacement Components Kit #LC359259 will work perfectly to replace both components. This will get your system back up and…

view full answer...

Answer 2

I reached out to my contact at Lippert and he said that it sounds like you have an older Power Gear Manual Leveling kit that had the ground running from the solenoid to the control board. This new kit, part #LC359259, can be used as a replacement but…

view full answer...

Answer 3

Hello again Michael. I'm sorry to say the Power Gear 500456 is an obsolete part. The entire kit #LC359259 is required for replacement to make it compatible with the old system. If you order the #LC82FR on its own it won't work with your…

view full answer...

Answer 4

To upgrade from your 500210 Power Gear Touch Pad you will in fact need the Replacement Lippert Components Power Gear Manual Leveling Control Kit #LC359259, which comes with a new touch pad, 8-pin harness and 6-pin harness. A 4-pin harness will not be…

view full answer...

Answer 5

Per the manufacturer when it comes to the shear pins being broken you would have to replace the whole Lippert Jack #LC298707 because the shear pins are not replaceable, and there is no way to fix them. What you will need to do is purchase a whole new…

view full answer...

Answer 6

The part number 1010000143 you mentioned cross references with the Power Gear part #LC386198 which is the left hand side replacement. The matching right hand side is the part #LC89CJ.

view full answer...

Answer 7

The Power Gear Motor 1010000155 has direct replacements of Replacement Motor for Lippert Power Gear Electric Leveling Jack System part #LC386198 or part #LC89CJ. These can actually be used on either side. I reached out to Lippert and they said to…

view full answer...

Answer 8

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 9

The High Pointe Built-In Convection Microwave with Air Fryer #HP36ZR will fit as a replacement for your current ECO28KD7. It does appear the new unit will easily fit into place but as the RV manufacturer can build 2 units at the same time and they be…

view full answer...

Answer 10

If the microwave you have is the High Pointe 520EC028KD7S the correct replacement would be the High Pointe part #HP49ZR.

view full answer...

Answer 11

Hey Bob! The High Pointe Built-In RV Convection Microwave #HP49ZR will fit right where your EC028KD7 is now with the same holes. This is actually the 520EC028KD7S so it shares the same model number and is a direct replacement. It also includes the…

view full answer...

Answer 12

They replaced your Kwikee step with a coach step. It really isn't an issue to do so just the assembly is different for the gear and motor than your previous step. The coach steps often have a separate switch inside the motorhome to turn off the…

view full answer...

Replacement Leveling System Module and Key Pad for Power Gear Part #500457

Featured Help Information

Miscellaneous Media

Continue Researching