Can 4.80-8 be Replaced with 5.70-8

Question

Question:

My current wheel setup on a light trailer is 4.80-8 and would like to upgrade to bigger tire like the 5.70-8 load C or D... if they will fit my wheel base. I have attached an image of my wheel lugs pattern for reference . Thanks.

asked by: Carl

0

Expert Reply:

The larger tire 5.70-8 like the part # AM10013 would work great in place of the tire you have now and would actually fit the same rim. Your picture didn't make it through but if you have a 5 lug wheel you'd want the # AM30153 or for a 5 lug wheel # AM30155.

expert reply by: Jameson C

0

Answer 1

The Kenda 5.70-8 tire you'd looked at, part #AM30140 has a maximum speed rating of 65 mph. If you were looking for something with a higher speed rating, you'll need to increase the wheel diameter up to a 12 inch wheel. The Taskmaster 4.80R12…

view full answer...

Answer 2

The thing about trailer tires is that unless otherwise noted they cannot exceed 65 miles per hour. It sounds like you exceed this speed and that is why you are getting vibration. Exceeding the speed rating will cause heat to build up in the tire and…

view full answer...

Answer 3

I have some great wheel and 5.70-8 tire options for you to choose from. It's very likely you have 5 on 4-1/2" pattern which measures 4-1/2" from bolt center to bolt center. There is no bolt pattern for a wheel this size which measures…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Can 4.80-8 be Replaced with 5.70-8

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching