Recommended Alternative Manual Crank Plug for an FIC Tongue Jack

Question

Question:

Hi Im looking for a manual crank plug for my FIC power tongue jack. The opening is a 1inch diameter, would you have anything that fits? Thanks!

asked by: JJ H

0

Expert Reply:

The closest I was able to find to what you're looking for was the Replacement Manual Override Cover for Bulldog Powered-Drive Trailer Jacks # BD500201.

This replacement rubber cap measures 1-1/8" in diameter and is 1" tall. I know it's a bit larger in diameter than what you're needing, but you can easily just shave off some size to fit your jack.

expert reply by: Bryce D

0

Answer 1

Hello Yeager, thanks for reaching out. Yes, the Progressive Dynamics 9300 Series RV Converter Charger #PD89RR is the recommended replacement for your PD9280A converter. It is capable of charging lithium batteries. There would be no real benefit from…

view full answer...

Answer 2

Hey Jerry, great question! Yes, if you found another slide out that is rated for only 5,000 RPM then you'll be cutting the movement of the slide just about in half. The Lippert Venture Actuator and High Speed Slide-Out Motor #LC168956 that…

view full answer...

Answer 3

Thanks for the picture and the dimensions. Based on what you have given me we have a couple of options for lug nut covers. The first is the Wheel Masters Lug Nut Covers - Stainless Steel - Ford - 1-1/16" - Qty 8 Item #WM8011 you referenced. This…

view full answer...

Answer 4

The Solera Gas Strut, 124 to 144 lbs for Pitched Awning Arms #LC260282 which is 24 inches or the Solera Gas Strut 26", 124 lbs for Short and Flat Awning Arms #LC280343 are the two options we have. They are shorter than what you describe by far.…

view full answer...

Answer 5

At this time we no longer offer the Atwood line of AC units so the only available options would be from Furrion or Advent Air. If you're just wanting to replace the rooftop unit and maintain use of your air distribution box and thermostat…

view full answer...

Answer 6

The dimensions I could find for a Norcold 1210 fridge are 68.88 T x 37.88 W x 28.75 D. The closest 12v fridge we carry to this size would be the Everchill RV Refrigerator w/ Freezer Drawer #WAY44FR, which is 28-1/2" wide x 72" tall (at…

view full answer...

Answer 7

You can look for the fuse and relay associated with that circuit and replace as needed to activate the 12 volt accessory circuit of the truck. Or, you can bypass the factory wiring and run a length of 10 gauge wire like part #10-1-1 (sold by the…

view full answer...

Answer 8

Yes, you are correct. The Dexter Nev-R-Adjust Electric Trailer Brakes item #K23-478-479 are exactly what you need for AL-KO 4,400 lbs axles.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Recommended Alternative Manual Crank Plug for an FIC Tongue Jack

Continue Researching