Do You Carry Rebuild Kits For the Master Cylinder on a Model 6 Surge Brake Actuator?

Question

Question:

Hi, do you have a reseal/rebuild kit for my Titan model 6 drum brake master cylinder? Thank you

asked by: Frank S

0

Expert Reply:

Currently we only carry the Replacement Master Cylinder Assemblies for Drum # T1777401 or Disc # T1777405 brake Model 6 surge actuators. We do not have any rebuild kits for these assemblies.

expert reply by: Bud M

0

Answer 1

Hey Dave, thanks for all the information. Sounds like you're really in a box here. You're going to have to move the spring seats regardless if you replace the axle because none of ours are in the same 70" position. To get more clearance…

view full answer...

Answer 2

If you replace the current brakes on your trailer with the same uni-servo drum brakes and no lockout actuator (like #T2351000), the brakes will deliver 20 percent braking when traveling in reverse. However, the more pressure you apply going backwards…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Do You Carry Rebuild Kits For the Master Cylinder on a Model 6 Surge Brake Actuator?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching