Correct Replacement Fill Cap for Dexter A60 Actuator

Question

Question:

I have a Dexter actuator and need a cap. The model is A60/A75/XR84. can you help? TX

asked by: Steve J

0

Expert Reply:

The correct replacement fill cap you need for your Dexter A60 Actuator is the Replacement Master Cylinder Filler Cap for Dexter Model 60 and Aero 7500 Actuators part # T4480701.

expert reply by: Conner L

0

Answer 1

Hi Gary; I'm sorry we don't have a video installing the #DX64XR at this time but I did go pull the installation manual out of the box for you. You need to remove the inner member and then route the cable as seen in the instructions. Dexter…

view full answer...

Answer 2

For your Magic-Tilt tandem axle boat trailer with disc brakes and a straight tongue I recommend Titan Disc Brake Actuator Coupler #T47457207K. This 7K bolt-on coupler has an electric lockout and I like it because it features a multi-ball fit so it…

view full answer...

Answer 3

Hey Jeff, yes the Tie Down U Bolt Spare Carrier part #TD38FR that you referenced will work great with a 13 inch spare like what your Karavan KCB 1800 has. This basically works with all trailer wheel sizes between 8 and 15 inch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Correct Replacement Fill Cap for Dexter A60 Actuator

Product Page this Question was Asked From

Continue Researching