Does Lid of MaxxFan Deluxe Need to be Up to Replace Lid

Question

Question:

Yo replace the lid on a max fan deluxe, do you need to disassemble the hinge that raise the lid? Or are the attachment points accessible independently?

asked by: Masa R

0

Expert Reply:

To access the screws needed to remove the vent lid of your MaxxFan to install the new # MA05-30520 you would need to raise the lid so that you can unscrew it from the base of the vent assembly. The screws are not accessible without having the lid up.

expert reply by: Jameson C

0

Answer 1

Tyler, great question - and it’s definitely more than cosmetic. The etrailer electric trailer jacks #e72QV and #e22QV are mechanically identical 3,500 lb jacks. Same motor, same lift height of 18", same 7-way plug power. The only difference is…

view full answer...

Answer 2

Hey Dan, good to hear from you again, although I do wish it wasn't because hail damaged your MaxxAir Deluxe Fan! The cover is replaceable and is available both in White #MA05-30510 and Black #MA05-30520. If you have a different MaxxAir Fan please…

view full answer...

Answer 3

To install a roof vent lid like the Replacement Lid for MaxxAir MaxxFan Deluxe #MA05-30510 for the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-05301K, isn't considered to be a difficult task at all. The unit does not have to be removed from the…

view full answer...

Answer 4

The MaxxAir FanMate Rain Cover, part #MA00-955003 is specifically designed to fit the MaxxAir MaxxFan. The MaxxAir MaxxFan like part #MA00-04500K fits in a standard 14-inch x 14-inch opening. As the attached video shows the rain cover part…

view full answer...

Answer 5

I believe you are referring to the lid, and while I can give you some options, you do need to know the type of MaxxFan vent you have. We have replacements for MaxxFan, MaxxFan Plus, and MaxxFan Deluxe roof vents, and you can take a look at the shapes…

view full answer...

Answer 6

There are not specific instructions on how to replace the Replacement Rain Shield for MaxxFan Deluxe Roof Vent - Smoke part #MA05-30520 on the MaxxFan Deluxe Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke part #MA00-06401K. However, replacement…

view full answer...

Answer 7

There is a replacement lid for the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-07000K - the part you're looking for is #MA05-30510. If you also need the Rain Shield Assembly then we have that as part #MA10-20204 as well.

view full answer...

Answer 8

I spoke with my contact at MaxxAir and was able to verify that the Replacement Rain Shield #MA05-30520 that you referenced will work perfectly as a replacement lid for your MaxxFan Deluxe Smoke 7500K Roof Vent #MA00-07500K. You will simply use…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Does Lid of MaxxFan Deluxe Need to be Up to Replace Lid

Product Page this Question was Asked From

Continue Researching