Does Rock Guard of 2020 GMC Sierra 2500 AT4 Get Trimmed to Install Curt Front Hitch C52NR

Question

Question:

2020 GMC AT4 2500 HD, does the plastic rock guard under the AT4 add any complexity to the installation?

asked by: Mike F

1

Helpful Expert Reply:

The rock guard of your 2020 GMC Sierra 2500 AT4 would need to get trimmed to install the Curt front hitch part # C52NR.

expert reply by: Jameson C

1

Answer 1

The Curt Front Mount Trailer Hitch Receiver #C52NR will fit your 2024 GMC Sierra 2500 AT4 but you will need to trim the rock guard in order for the hitch to fit.

view full answer...

Answer 2

Yes, the Curt Front Mount Trailer Hitch Receiver #C52NR is a confirmed fit for your 2024 GMC Sierra 2500. I've attached a short video below where Jake will walk you through the installation process.

view full answer...

Answer 3

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi Eric, Thanks for your question. As long as you are able to remove the factory hitch from your 2025 GMC Sierra 2500, the #C96CR will work as a replacement. Of note, the #C96CR will more than likely mount up a bit differently than your factory…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Does Rock Guard of 2020 GMC Sierra 2500 AT4 Get Trimmed to Install Curt Front Hitch C52NR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching