Recommended Mounting Bracket For Pollak 5-Pole, Round Pin Trailer Wiring Socket # PK11502

Question

Question:

I don’t know which mounting bracket works for PK #11502

asked by: David S

0

Expert Reply:

I recommend the Hopkins Mounting Bracket # HM48605 for securing the Pollak 5-Pole, Round Pin Trailer Wiring Socket # PK11502. The Hopkins bracket has a slit in the bottom which allows you to easily attach and remove the connector without having to remove all the wiring from the connector.

expert reply by: Bud M

0

Answer 1

There are 5-way rounds like the part #PK11502 and there are 5-way flats like the #HM47900. I am not sure which you have tried but it sounds like your motorcycle uses a unique style of connector. Which if you have the #PK11502 already you could just…

view full answer...

Answer 2

There is not an adapter so you'd need to make your own for your trailer with a 5-round connector like #PK11501. What you'd need to do is cut off the end of your 4-way and connect the wires to the terminals of the 5-Pole, Round Pin Trailer…

view full answer...

Answer 3

Functionally speaking, there isn't a huge difference. The Curt #C56382 has a slightly lower capacity at 3 amps for circuit for stop/turn signals and 6 amps for taillights. The Tekonsha #118781 has a capacity of 5 amps per stop/turn circuit and…

view full answer...

Answer 4

The Pollak 5-Pole, Round Pin Trailer Wiring Sockets, item #PK11502, and #PK11501, do not have a standardized wiring configuration. I normally direct my customers to the 6-way wiring configuration, eliminating the middle pin. Start by wiring the top…

view full answer...

Answer 5

There is no adapter to go from a 4-Way flat to a 5-Way round connector so you have a couple of options. What I would do is to install a 4-Way flat using #119178KIT. Then use a 4 to 5-Way flat adapter, #20036. The extra wire on the adapter, normally…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Recommended Mounting Bracket For Pollak 5-Pole, Round Pin Trailer Wiring Socket # PK11502

Product Page this Question was Asked From

Continue Researching