Replacement Tail Light For Wesbar Wrap Around Trailer Tail Light

Question

Question:

Do you have a sister part to 105825 - a wraparound replacement lens, drivers side? Thank you

asked by: Adam L

0

Expert Reply:

I recommend replacing your Tail Lights with the Drivers # STL37RPG and Passengers # STL36RPG lights as the Wesbar Lights and lenses are obsolete. The Optronics lights above will both use the same Tail Light Lens # A39RB if either side were to become damaged. So you will only need to keep one spare on hand versus having both sides and only damaging one side.

expert reply by: Bud M

0

Answer 1

Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…

view full answer...

Answer 2

The Wesbar Wraparound LED Tail Lights part #271594 for passenger or part #271595 for driver appear to be very similar to that of those on your 2002 Ranger 620VS Boat Trailer so they should work in their place just fine. The Wesbar Wraparound LED Tail…

view full answer...

Answer 3

For an LED replacement that is nearly identical to the Wesbar 105826 light you can use #STL36RB for the right side and #STL37RB for the left side. There are also versions that have a plug instead of just bare wires. For the right side use #STL36RPG…

view full answer...

Answer 4

Hi Jim! The Wesbar Wrap Around Lenses were discontinued quite a while ago, so unfortunately, we do not have any left in stock. I did a lot of searching around the web, but I was unable to find anywhere that still carries them. You may be able to find…

view full answer...

Answer 5

For the Optronics trailer taillights #STL36RPG and driver side #STL37RPG we do carry the style of connector it uses with the part #9651P. You'd cut the harness in half and wire either side to your trailer wiring so that you can easily connect to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Replacement Tail Light For Wesbar Wrap Around Trailer Tail Light

Product Page this Question was Asked From

Continue Researching