Upgrading To LED Tail Lights On a Ranger 620VS Boat Trailer

Question

Question:

need replacement lights LED for both sides currently has wesbar lights that are burnt out

asked by: Chad M

0

Expert Reply:

The Wesbar Wraparound LED Tail Lights part # 271594 for passenger or part # 271595 for driver appear to be very similar to that of those on your 2002 Ranger 620VS Boat Trailer so they should work in their place just fine. The Wesbar Wraparound LED Tail Lights are submersible so you won't have any issue here either. The plug from the rear of the lights can be removed if it does not match what you have on your trailer now. These will be the best replacement option we have for your trailer at this time.

expert reply by: Conner L

0

click to enlarge

Answer 1

Hey Jeff, we do have some good replacement options for you. The Wraparound LED Tail Light 271594 has unfortunately been discontinued. Our best option for replacing it is the ONE LED Trailer Tail Light #STL0066RBG for the passenger side and…

view full answer...

Answer 2

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…

view full answer...

Answer 9

Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…

view full answer...

Answer 10

Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…

view full answer...

Answer 11

No, it is not plug and play Paul but it can be. The TecNiq Contoured Seven Function Box Style Tail Light item #TN62XR passenger side and item #TN42XR driver's side use a 3-Prong PL-3 Plug like item #TN47PV. These lights measure 7-1/2" long x…

view full answer...

Upgrading To LED Tail Lights On a Ranger 620VS Boat Trailer

Continue Researching