Correct Replacement Pitch Arm for Solera 63" Awning Support Arm

Question

Question:

I bent the 63 lippert adjustable pitch awning arm. Can I replace with a 69 lippert awning arm? I have room for extra length. This is for a 2022 KZ Esacpe E20 Hatch

asked by: Michael M

0

Expert Reply:

If your existing support arms measure 63" long end to end then the correct replacement pitch arm is the Replacement Pitch Arm for Solera XL Flat RV Awnings part # LC67VR for black or part # LC62NJ for white. The pitch arm for a 69" long support arm will not fit.

expert reply by: Conner L

0

Answer 1

Thanks for the photos, and from that it looks to me like you are asking if just the pitch arm assembly is available, and if so, the answer is yes, it is the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm…

view full answer...

Answer 2

Hello Wende, thanks for reaching out. We do offer replacement pitch arms for the Solera brand awnings, which are made by Lippert. I do not have a way to look up your camper to know exactly what brand or size of awning you have now. I need to know the…

view full answer...

Answer 3

We have replacement pitch arms for the Solera 69 inch awning setups like what you have with the part #LC375994 which would be all that you'd need.

view full answer...

Answer 4

It looks like the closest we have to those measurements is the Replacement Support Arm Assembly for Solera Pitched RV Awnings LC260294 which measures 66 1/8" long. Just to be clear, you will need to measure the wall mount from the top to the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Correct Replacement Pitch Arm for Solera 63" Awning Support Arm

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching