Availability of Replacement Rear Jack Leg For Lippert 2.0 Electric Leveling System

Question

Question:

Is it possible to get just the leg for the rear jack on a lippert 2.0 leveling system

asked by: Don E

0

Expert Reply:

Yes, the Replacement Heavy-Duty Landing Gear Jack Leg # LC241844 will replace a rear leg for your Lippert 2.0 electric leveling system.

expert reply by: Bud M

0

Stan

7/1/2024

Is there a repair kit for the rear jack on a lippert 2.0 leveling system

Bud M.

7/8/2024

@Stan Lippert does not offer a repair kit for the jacks on your Lippert 2.0 Leveling System. You will need to get a new Rear Jack # LC241844.

Answer 1

There is a great chance either of the legs you mentioned would work as a replacement, but I'd need to know for sure what landing gear you have on your trailer. The Lippert landing gear like the part #LC179013 and #LC179014 are very popular and…

view full answer...

Answer 2

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 3

I do have an option for you but in order to confirm the correct replacement landing gear leg screw for you, I would need to know the model number of the jack. If you can provide this for me then I can go about seeing if we have the correct landing…

view full answer...

Answer 4

The correct landing gear leg replacement for the Lippert Ground Control 2.0 that you have is actually the part #LC241846. We have no way of knowing if the #LG-179013 could work for you since it's never been tested although I can see how it looks…

view full answer...

Answer 5

We sure do Billy! That 241846 part number you gave me corresponds to the Replacement Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear item #LC241846. The item #LC241846 is intended to replace the heavy duty master leg on Lippert…

view full answer...

Answer 6

I sent all of this to my tech contact at LCI to see what they this is the problem and they were able to come up with a way to use the voltage readings to determine where the issue is: There are 4 wires on the harness as follows Black= power (need to…

view full answer...

Answer 7

If you're referring to the control module #LC85ED for your Ground Control 3.0 #LC675817 then yes, each fuse is to power each individual leg and should be labeled with which specific leg. If you're moving the slides at the same time while the…

view full answer...

Answer 8

Sounds like it could be a bad control module, if this is the case, you would need to replace your #LC675817, but let's first troubleshoot to determine this. The first thing you are going to want to do is check for blown fuses on the control…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Availability of Replacement Rear Jack Leg For Lippert 2.0 Electric Leveling System

Product Page this Question was Asked From

Continue Researching