Does Dometic 511 RV Toilet Use Sam 4 Bolt Mounting Flange as 311 Toilet

Question

Question:

Hey guys, I currently have a Dometic 511 plus toilet in our 2003 lazy daze RV. The toilet is original I would like to replace the whole thing. I’m looking at your Dometic 311 low profile toilet. Would I have to get a new flange for it as well? I believe the current Dometic 511 is four bolt.

asked by: Brian A

0

Expert Reply:

Since the Dometic 511 uses a 4 bolt mounting flange you would not need to replace that when going to the Dometic 311 toilet part # DOM67FR that you are interested in.

expert reply by: Jameson C

0

Answer 1

The correct replacement circuit and control board for your Lippert Electronic leveling system is the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System #LC421484. This will be a plug and play solution, so…

view full answer...

Answer 2

The 2018 Ram Promaster isn't prewired for a brake controller, but installing one is a pretty straightforward process. Tekonsha provides a ready made wiring harness/7-way trailer connector as part #22112 that when combined with the Tekonsha Primus…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Does Dometic 511 RV Toilet Use Sam 4 Bolt Mounting Flange as 311 Toilet

Continue Researching