Install Video of Universal Installation Kit for Trailer Brake Controller on 2009 Toyota Highlander

Question

Question:

Hello, Does the brake control install described in the 2010 Toyota Highlander video apply to the 2009 Toyota Highlander Hydrid also? The parts were 90195 brake controller, the ETBC7 kit, and 18136 bracket kit. Just wanted to verify that before buying those. Thanks, Tim

asked by: Tim

0

Expert Reply:

The 2009 Toyota Highlander is the same generation as the 2010 Toyota Highlander so the install video attached below of the Universal Installation Kit for Trailer Brake Controller part # ETBC7 on a 2010 will be the same as your 2009. It will pair perfectly with the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 and Curt T-Connector Vehicle Wiring Harness part # C56217.

expert reply by: Conner L

0

Answer 1

You've installed everything correctly. The brake controller is intentionally wired directly to the battery, so there's no chance the user will forget to turn it on. This is done as a safety measure, and it's not recommended to install it…

view full answer...

Answer 2

According to my research, the Toyota Highlander doesn't have the connector under the dash to install a brake controller. In order to install your brake controller, you'll need to hardwire the controller using our Brake Controller Installation…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Install Video of Universal Installation Kit for Trailer Brake Controller on 2009 Toyota Highlander

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching