Is There a Torque Spec For Yakima Replacement 2" Anti-Rattle Hitch Bolt Assembly

Question

Question:

What is recommended torque spec for the bolt tightened down to the hitch? What size socket is needed for the hex head?

asked by: Jonathan N

1

Helpful Expert Reply:

I checked with Yakima and there is not a specific torque spec for the Replacement 2" Anti-Rattle Hitch Bolt Assembly for Yakima Bike Racks and DryDock Load Assist # Y8780022.

So you'll just want to torque it until it is tight, and you can use either a wrench or a 3/4" socket.

expert reply by: Kyle S

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 4

Hey Brian. The Curt Trailer Connector Adapter item #C57672 is going to install in the same way on your 2023 F-150 as it did on the video we made for a 2021 F-150. Those trucks are the same generation but I can not guarantee the wiring colors are…

view full answer...

Answer 5

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 6

Hey Gregory, that's really good information. You’ve got a few options, but I wouldn’t jump straight to replacing the leaf springs on a half-ton for that size trailer. Since you’re using a Curt weight distribution hitch, that should be doing most…

view full answer...

Answer 7

Unfortunately you can not Doug. The factory hitch on your 2020 Ford F-150 Lariat is part of the rear step-bumper assembly. It's bolted to your frame and then the step-bumper bolts to the trailer hitch. Removing the factory hitch removes the…

view full answer...

Answer 8

Hi Jeff, The K-Source Snap & Zap Custom Towing Mirrors part #KS69NQ will work with your Lariat mirrors while allowing you to retain the use of the camera and side lights! These mirrors are specifically designed to match the contours of the side…

view full answer...

Answer 9

Hey Richard, yes you can set the tension in the springs of the RoadActive Suspension Kit part #RAS3611-Y low enough so that the suspension height is not raised at all. If you add in a lot more tension it will slightly affect the ride height like you…

view full answer...

Answer 10

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 11

Hi Richard! The best brake controllers on the market for your 2023 Ford Explorer XLT are going to be from Redarc. They're super easy to use and set up, and they are very reliable. They are the ones to get. Since you said you will be towing a…

view full answer...

Answer 12

Hey Phil, If you're looking for the factory wire harness for a plug and play connection you'll find a connector that's gray with a red/orange center like the plug on the Curt Custom Wiring Adapter for Trailer Brake Controllers #C51436.…

view full answer...

Is There a Torque Spec For Yakima Replacement 2" Anti-Rattle Hitch Bolt Assembly

Continue Researching