What is Size of Mounting Ball on Furrion Vision S Monitor

Question

Question:

Can the screen be mounted to a Bullet proof mount system, if so what size ball mount does it require?

asked by: Tandra

0

Expert Reply:

Hey Tandra, we haven't tested the Furrion Vision S + systems like the part # FR57AD on a Bulletproof mount system at this time but I can tell you that the diameter of the ball is 5/8 inch. Is that the correct size for that system?

expert reply by: Jameson C

0

Tandra

7/21/2026

I went to there website, they have a few different sizes. I ordered a kit with multiple sizes so we will see.

Jameson C.

7/21/2026

@Tandra Right on! Yeah let us know if it works!

Answer 1

*Updated From Below Hi Michael; I'm sure you're right, it is probably prepped for the Furrion. Since Furrion is phasing out the old Vision S, and parts won't be available soon, you want to get the new Furrion Vision S+ Wireless RV Backup…

view full answer...

Answer 2

Hey Mike, your 2025 Chevy Silverado 2500HD will have the power issue with the Furrion Vision S + #FR57AD that you have so you would need a solution like the part #VGR64VR that you referenced. Or if you don't want to mess with any wiring you could…

view full answer...

Answer 3

Hey, Joe. That's a great question. Backup cameras and rearview, observation, cameras are essentially the same, the difference comes down to how they’re wired. With a system like the Furrion Vision S+ Wireless RV Backup System #FR57AD, it’s…

view full answer...

Answer 4

Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.

view full answer...

Answer 5

Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera #FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire…

view full answer...

Answer 6

Hey Michael. The backup camera that comes with the Furrion Vision S+ System item #FR57AD has built in mounting holes in the casing. It comes with four #6 x 3/4" flat head self-tapping screws, four #4 x 1/4" self-tapping screws, sealant, and…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Hi Mark, You shouldn't need to use the Furrion 7-Way Vehicle Power Adapter part #FR87PR because your 2018 Ram 2500 is from the fourth generation of the Ram 2500 before they did the huge overhaul that changed the circuits and resulted in the newer…

view full answer...

Answer 10

Hey Tandra, we haven't tested the Furrion Vision S + systems like the part #FR57AD on a Bulletproof mount system at this time but I can tell you that the diameter of the ball is 5/8 inch. Is that the correct size for that system?

view full answer...

Answer 11

Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…

view full answer...

What is Size of Mounting Ball on Furrion Vision S Monitor

Product Page this Question was Asked From

Continue Researching