Recommended Fold-Away Coupler Hinge Kit for a 2 Inch Trailer Coupler

Question

Question:

Do they make a 2 x 2 folding coupler for a trailer tongue?

asked by: Samuel S

0

Expert Reply:

I have solution for you but we do not have any folding coupler hinges for a 2" x 2" coupler. You can weld 1/2" plates to the top and bottom of the coupler and use either the Bolt On Fold-Away Coupler Hinge Kit item # FHDPB230101 or Weld On item # FHDPW230300. Both of this kits are rated for up to a 5,000 lbs trailer.

I have linked an installation video below.

expert reply by: Jerred H

0

Answer 1

Hello Chris, Yes, it would be quite difficult to find a replacement master cylinder for your Dexter model LP75. The brake actuator was actually a Tie Down Engineering part that Dexter took over as Tie Down Engineering is no longer in business but…

view full answer...

Answer 2

Hey, Tom. Thanks for your question. The Replacement Extra Long Trailer Tongue for CE Smith Multi-Sport Trailers #CES45FR can work for your setup, but there are a couple things to keep in mind. Since it’s longer than your current tongue, 2x3 vs yours…

view full answer...

Answer 3

Paul, yes it does matter which battery cable is disconnected to flat tow your Silverado. since your owner's manual calls for the negative side to be disconnected, you'd just need to hook up the Roadmaster Battery Disconnect with Switch for…

view full answer...

Answer 4

To measure for a fold-away trailer tongue hinge you want to first measure the size of your trailer tongue, for example Fulton Fold-Away Coupler Hinge part #FHDPB330301 is for 3" x 3" trailer tongues. To determine where to cut the tongue,…

view full answer...

Answer 5

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Recommended Fold-Away Coupler Hinge Kit for a 2 Inch Trailer Coupler

Featured Help Information

Miscellaneous Media

Continue Researching