Can the Draw-Tite Trailer Hitch for a 2020 Infiniti QX50 Be Used to Tow a Trailer

Question

Question:

Can i tow a jetski and jetski trailer with this hitch?

asked by: Diego E

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76240 which is a fit for a 2020 Infiniti QX50 has a 4,000 lb gross trailer weight rating. That said, if the vehicle is rated lower that's the figured you'll need to abide by. This figure can be found in your owner's manual. Therefore, so long as the weight of the trailer and cargo is below the tow capacity of the vehicle (check owner's manual) you'll be good to go.

Please note, in order to complete your setup you'll also need a trailer wiring harness like the T-One Vehicle Wiring Harness part # 118796 and a ball mount/hitch ball like the Curt Towing Starter Kit part # C45534.

expert reply by: Conner L

0

Gary

3/9/2024

With this hitch, will my hands free lift gate still work?

Mike L.

3/10/2024

@Gary The feature will work, but not directly under or next to the square receiver tube. The sensors to the right and left of the receiver will still pick up movement and operate the liftgate.

Answer 1

Yes, because of you we were able to confirm that the Curt Hitch part #C86QV does fit your 2023 Infiniti QX55.

view full answer...

Answer 2

To remove the taillights of your 2019 Infiniti QX50 so that you can install the trailer wiring kit part #118796 you will need to remove the two screws you mentioned and then pull straight back and not to the sides.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can the Draw-Tite Trailer Hitch for a 2020 Infiniti QX50 Be Used to Tow a Trailer

Products Featured in This Question

Continue Researching