How to Mount 6,000LB Under Slung Axle Under The Leaf Spring

Question

Question:

Can the axle be mounted underneath this spring?

asked by: Richard L

1

Helpful Expert Reply:

To mount an under slung axle like the Dexter Trailer Axle # 8327826-EB below a set of the 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles # e88SR you will need an over-under kit. The Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00 will fit the 3" diameter 6,000lb axle I linked above.

expert reply by: Bud M

1

Answer 1

When using the 5-Leaf Double-Eye Spring #e34SR the recommended spacing between front and center hangers and between rear and center hangers is 29-1/2-inches; recommended distance between u-bolts is 33-1/2-inches and the distance from the axle center…

view full answer...

Answer 2

The best solution to lift a tandem axle trailer like yours 2 inches is the 2 inch lift for tandem axles from Lift Kit #RR23QX. This attaches to the suspension hangers and gives you a safe and very stable 2 inch lift like you are needing!

view full answer...

Answer 3

Thank you the pictures are a great help. I recommend using the MORryde AllTrek 4000 Equalizers #MR29DR with the MORryde Suspension Upgrade Kit for Triple Axle Trailers - 3-1/8" #MR26ZR for your 2015 Keystone Carbon 327 5th wheel camper. These…

view full answer...

Answer 4

If your existing leaf springs measure 25-1/2" then the correct replacement is likely either 25-1/8" or 25-1/4" as leaf springs stretch over time. Please note, leaf springs should also be measured with the trailer unloaded. I have…

view full answer...

Answer 5

Since leaf springs flatten out as they wear, the best way to determine their actual center eye to center eye length is to put the trailer up on jack stands so the axle(s) hang freely, then measure them. This being said, there's every chance that…

view full answer...

Answer 6

Hi Jeff; to find the right replacement leaf springs you will need to know your axle capacity and find their length. If you don't already know the capacity, check the axle tag to see if it is listed. If you only have a serial number the axle…

view full answer...

Answer 7

Our U-Bolt kits are available separately due to axles having different sized and most hanger kits can be used with several different size axles. Here is a list of different size kits depending on your axle size. 1-3/4" Round Axle #CE23000…

view full answer...

Answer 8

Hello Steve. Thank you for emailing me the picture of your suspension, as they are always most helpful. Leaf springs have the tendency to stretch out over time which does not give us an accurate measurement, so with your leaf springs measuring at…

view full answer...

Answer 9

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

view full answer...

Answer 10

Thank you providing that measurement. Since you have a 33" wheelbase that is correct, you need the #MR87ZR. To choose the right MORryde Suspension Upgrade Kit you will also need to measure your shackle straps. If they measure 2-1/4" from…

view full answer...

Answer 11

It sounds like you are definitely on the right track here. The #MR79ZR is indeed the correct suspension upgrade kit for your 2007 Colorado 5th wheel with LRE suspension. Moryde makes a fantastic suspension upgrade kit. The heavy duty shackles and wet…

view full answer...

Answer 12

We have a handful of 6K leaf springs, like the part #e94SR you were looking at, that could potentially work for your Montana High Country but I'll need you to measure the distance from the center of one eyelet to the center of the other eyelet to…

view full answer...

How to Mount 6,000LB Under Slung Axle Under The Leaf Spring

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching