Types of Motorcycle Wheel Chocks Available

Question

Question:

Do you have wheel chocks for motorcycles?

asked by: Geoff

0

Expert Reply:

We do have wheel chock for motorcycles. If you have e-track in your trailer the CargoSmart Motorcycle Wheel Chock # 3481731 will snap into the track allowing you to easily remove it when not needed. The Tow-Rax Removable Wheel Chock w/ Wood Screws # TWSPWC is a more basic chock. It includes mounting screws for securing to wood floors used on several utility trailers.

expert reply by: Bud M

0

Answer 1

Rather than using the CargoSmart Motorcycle Wheel Chock #3481731 and having to install different E-Track #SLSB mounts onto your floor you should consider the Wheel Chock #EM07506. This chock cradles the front tire which allows the bike to sit more…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Ross, the B and W Turnoverball #BWGNRK1067 wasn't designed to fit under a flat bed so there isn't an alternate set of measurements I can recommend. Are you sure it would clear under the flat bed? Normally we have to recommend the…

view full answer...

Types of Motorcycle Wheel Chocks Available

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching