See what our Experts say about this Tow-Rax Wheel Chocks

• Recommended Wheel Chocks for Motorcycle Carrier
  I like the Tow-Rax Removable Wheel Chock, # TWSPWM in black and # TWSPWC in chrome. These can be screwed down to a wood floor of a trailer but also bolted down using the included hardware. These are 8-3/8" wide and from specs available to me online, the MotoGroup, ST3402 carrier has tracks 7-1/2" wide, this option will set slightly over the edge the carriers rails. That does not prevent this being used but I think setting within the rails may make a better fit. You would need to fabricate...
  view full answer...
  
• How To Set-Up Demco Hijacker 5th Wheel Hitch When Using Rhino Box Pin Box
  What I think you are asking is, how to set-up the hitch with the Rhino Box as the narrow width of the pin box does not engage the capture plates on your Demco Hijacker 5th Wheel hitch. What you are missing is the Demco Hijacker Autoslide Locking Plate for Lippert Rhino Pin Boxes, # DM76FR. You need to use this locking plated when using a Lippert Rhino pin box with the Demco hitch.
  view full answer...
  
• Types of Motorcycle Wheel Chocks Available
  We do have wheel chock for motorcycles. If you have e-track in your trailer the CargoSmart Motorcycle Wheel Chock # 3481731 will snap into the track allowing you to easily remove it when not needed. The Tow-Rax Removable Wheel Chock w/ Wood Screws # TWSPWC is a more basic chock. It includes mounting screws for securing to wood floors used on several utility trailers.
  view full answer...
• E-Track Spacing Recommendation for Securing a Harley To a Utility Trailer
  If you can get your tie down straps around 45 degrees or slightly higher when securing your Harley you would be setup pretty good. This number is more of a guideline than a rule though. Your best bet would be to mock up everything first and then make sure everything would fit properly. Put your bike in the trailer and then determine where they best place to locate the tracks would be. For D-rings to use with the E-track you would want the part # E59143, for backing plates for installing...
  view full answer...
• Tie Down System To Secure A Large Motorcycle For Travel
  Tow-Rax Low-Profile Floor Track for Tie-Down Anchors - Aluminum - 6' Long - Machined - Qty 1 # TWSP72TA. This system when using the Tie-Down Anchor for Tow-Rax Low-Profile Floor Track - 1,666 lbs - Qty 1 # TWSPDSTD225 have a working limit of the 1666 lbs listed and a break strength of 5000 lbs. I recommend using a system like this along with something like the Tow-Rax Removable Wheel Chock w/ Wood Screws - 6-1/2" Wide Tires - Tubular Steel - Chrome # TWSPWC. For tie down straps, I...
  view full answer...
• Motorcycle Wheel Chock in Toy Hauler Recommendation Where Under Trailer Access is Limited
  You could use the Tow-Rax Removable Wheel Chock # TWSPWC. You would not need to access the bottom of your trailer to install the install hardware. All you would need to do is drill hole for the anchors of the wheel chock and then you would be able to use the install bolts that thread into the anchors to secure the # TWSPWC. I attached a review video for this product for you to check out as well.
  view full answer...
• Recommended Wheel Chock for Suzuki Burgman Scooters
  The 4-3/4 inch wide front tires of your scooters would be perfectly compatible with the Tow-Rax # TWSPWC wheel chock. The chock includes hardware for mounting the chock to a wood floor, for a metal floor you'd need the # TWSPWFKM mounting hardware. If you don't already have them, you'll also need some ratchet straps to hold the scooters in place. Ones set of # 05605 straps per scooter would have plenty to capacity to keep the scooters locked into position.
  view full answer...
• Options for Securing Harley-Davidson Motorcycle in Garage of Toy Hauler
  The combination of the existing D-rings and the wheel chock that uses the # TWPH2770 mounting hardware for the # TWSPWC sounds as if it'd be an ideal solution for you. Installing the # TWPH2770 would involve drilling holes through the floor of the garage of your toy hauler, but once the mounts were installed, the chock can easily be installed and removed as needed. We don't carry the Condor chocks, but we do offer a some chocks. If you're only planning on carrying the Harley on your Toy...
  view full answer...
• Can a Wheel Chock be Safely Mounted to and Used on a Plywood Floor
  Since the floor of the trailer is 1/2 inch thick plywood I recommend mounting the Tow-Rax wheel chock # TWSPWC through the floor and attaching it directly to the frame of the trailer. Or, as an alternative, you could attach a steel backing plate on the other side of the plywood floor and attach the chock to that. This will disperse the weight better. Once you have the chocks secured in one of the manners above and tie down the bikes it will be safe!
  view full answer...
• Quick Release Motorcycle Wheel Chock Recommendation
  I have a solution for you, but the Wheel Chock MTMWC-01R is designed for permanent install. Instead you might be interested in the # TWSPWC which has slotted install holes so that you can slide the chock backwards and remove it easily when needed. I attached an install video for you to check out as well.
  view full answer...
• Will Tow-Rax Mounting Hardware For Wheel Chock Withstand The Weight Of A Harley
  Yes, the mounting hardware part # TWSPWFKM is designed to mount Tow-Rax motorcycle chocks like part # TWSPWC onto a metal floor. The hardware is designed to withstand the weight of a motorcycle such as your Harley but I contacted Tow-Rax and they could not give me an official weight rating. I have attached a video for your reference.
  view full answer...
• Recommended Removable Wheel Chock for 2016 Indian Vintage Motorcycle
  Great news! I found that the width of your 2016 Indian Vintage's front tire is just over 5 inches. This will work great with the removable Tow-Rax Wheel Chocks. Depending on what type of trailer floor you have we off the wood screws with chock in black # TWSPWM or chrome # TWSPWC. We also have a chrome with multi-surface mounting kit for metal or wood floors # TWSPWC3BT. Any of the Tow-Rax Wheel Chocks can use the metal floor hardware kit # TWSPWFKM sold separately. I have linked a...
  view full answer...
• What is the Height of the Pivoting Bracket on MaxxTow Wheel Chock # MT70075
  The top edge of the pivoting bracket on the rear of the MaxxTow Wheel Chock (DISCONTINUED) will sit at most 10-inches above the surface of the unit's base. Its height varies slightly depending on the position of the bracket - in other words depending on where it is in its arc of rotation. This position varies, naturally, by tire diameter. Tires up to 5-1/2-inches wide will fit the chock and it includes mounting hardware. We also offer a chock from Tow-Rax, either # TWSPWM in black or...
  view full answer...
• How to Install Tow-Rax Removable Wheel Chock w/ Wood Screws
  We don't currently (April 2022) have an installation video of the Tow-Rax Removable Wheel Chock w/ Wood Screws # TWSPWC but the installation process is pretty straightforward. You'll need to use a 3/8" drill bit and drill your holes in your floor either using the attached diagram as a guide or by holding the chock where you'd like it located and making marks through the mounting holes. I recommend going the second route. After the holes are drilled out you'll insert the anchors and secure...
  view full answer...
  
• Capture Plate Kit Needed For A Demco Hijacker And Pin Box Connection
  If you're referring to the locking plates that sit on the head of the Demco Hijacker and clamps onto the pin box to lock the head to it then you'll need part # DM6171 if you have a Trailair or Rota-Flex pin box or part # DM76FR if you have a Lippert Rhino pin box. Based on your description of the pin box you most likely have the Lippert Rhino so you'd want to go with the # DM76FR. If it is a Rhino then it will should have Rhino labeled on the sides and possibly also the front.
  view full answer...
• Can etrailer Cargo Carrier for RV Bumper Carry Dirt Bikes
  As far as weight capacity goes the 24x84 etrailer Cargo Carrier for RV Bumper # e96ZR has a 500 lb weight capacity so it can handle the bikes, but the thing you're going to have to check is the weight capacity of your bumper as it will likely be less than that. This carrier weighs in at 82 lbs and mounts directly to the bumper so you'll have to subtract the 82 lbs from the weight rating of your bumper so get an accurate rating. When it comes to securing your dirt bikes that is another...
  view full answer...
• How to Determine Wheel Chock Placement In Toy Hauler to Avoid Hitting Tanks Underneath
  You'll either need to have the trailer manufacturer give you a layout of the tanks or you'll need to gain access underneath to physically determine where the tanks are. Aside from that there isn't a special way to determine this that we know of. This is the same case for the Tow-Rax Removable Wheel Chock # TWSPWC and Mounting Hardware # TWPH2770.
  view full answer...
• Need Replacement Mounting Hardware for the Tow-Rax Removable Wheel Chock w/ Wood Screws TWSPWC
  The replacement hardware screws that come with the Tow-Rax Removable Wheel Chock w/ Wood Screws, part # TWSPWC, are listed as part # TWSPWFKW. If you need to mount the Tow-Rax Removable Wheel Chock to a metal floor then you will want part # TWPH2770, which includes mounting hardware for both wood and metal flooring.
  view full answer...
• Wheel Chock Recommendation to Carry a Honda CRF250L in the Bed of a Truck
  Since you want to install a chock in the bed of your truck I recommend something that is easily removable so the bed is clear when you need it to be. For that I recommend using Tow-Rax Removable Wheel Chock # TWSPWC with mounting hardware kit # TWPH2770 for metal floors. I have linked a video review of this chock for you. This does mean you would have to drill through the truck bed. I also recommend using handlebar straps # 06303 in conjunction with ratchet straps such as # EM05729 when...
  view full answer...
• How To Mount The Tow-Rax Wheel Chock In The Bed Of A Pick Up Truck
  To mount the Tow-Rax Removable Wheel Chock # TWSPWC in the bed of your pick up you could use the Mounting Hardware for Tow-Rax Removable Wheel Chock - Multi-Surface # TWPH2770. This would require you to drill into the bed to allow bases and bolts to pass through and mount the wheel chock to the bed.
  view full answer...
• What is the Difference Between the Tow Rax Motorcycle Wheel Chocks TWSPWC3BT and TWSPWC
  The difference is the included mounting hardware. The # TWSPWC3BT comes with anchors and hardware to attach to metal or wood floors whereas the part # TWSPWC only comes with wood screws. I attached a review video for both chocks for you to check out as well.
  view full answer...
• Mounting Pinball Machines, E-Bikes, and Motorcycles in a 6 x 10 Enclosed Trailer
  The absolute best option would be to purchase a few sets of the CargoSmart X-Track Cargo Organizer Pro Bundle - Matte Black - Steel - 667 lbs - 5' Long # 3481788-P. Since it is most likely that you need more straps than tracks, I recommend more of the CargoSmart Ratchet Straps for E-Track or X-Track - 2" Wide x 12' Long - 1,000 lbs - Qty 2 # 3481935 depending on how secure you want your cargo. With this setup, you will have multiple mounting point locations on your trailer for safe transport....
  view full answer...
• Would Tow-Rax Wheel Chocks # TWSPWC Work on a 2003 Harley Superglide
  Yes, the Tow-Rax Wheel Chocks # TWSPWC can work on tire widths that are up to 6-1/2 inches wide so yours that is right around 4 inches wide would work perfectly. I attached a review video for this chock for you to check out as well.
  view full answer...
• Availability of Removable Wheel Chock for Dirt Bike
  The MaxxTow Adjustable Wheel Chock (DISCONTINUED) MT70075 is not removable but we do have motorcycle/dirt bike wheel chocks that are removable. The Tow-Rax Removable Wheel Chock # TWSPWM in Black or # TWSPWC in Chrome is removable and can accommodate tires that are up to 6-1/2" wide. These come with wood screws but if you have a metal floor then you can use the mounting hardware # TWSPWFKM. All of our adjustable wheel chocks are meant to be mounted permanently so if you are really wanting...
  view full answer...

Do you have a question about this Wheel Chock?