Does Ball of Curt Rockerball Arrive Installed and Torqued Down

Question

Question:

Is the ball factory-torqued to the hitch already, or they will arrive in two separate pieces?

asked by: Kai Z

1

Helpful Expert Reply:

The ball of the Curt RockerBall 2-5/16" Shock Absorbing Hitch Ball and Ball Mount w/ Sway Control Tab # C45WR is not installed or torqued down when it arrives. You'll need to torque the nut to 250 ft lbs.

expert reply by: Jameson C

1

Answer 1

Hey Justin! I’d look at the etrailer Sidewind Trailer Jack - Swivel Bolt - 2K #e35YV for that. It mounts to the trailer frame instead of staying in the center A-frame jack location, and it fits trailer frames 2" to 4" tall; it should fit…

view full answer...

Answer 2

The anti-swivel base on the #C45WR is missing a tab on one side to make it compatible with the sway control tab. This does not adversely impact the performance. You can use the #C40047 with the #D320 but you would have to bend or cut one of the tabs…

view full answer...

Answer 3

Going with the #C40047 Curt Rocker Ball will help isolate some of the clattering and banging from the surge coupler, and it will also help dampen some of the road shock you experience. What it won't do is help with the movement of the ball mount…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Does Ball of Curt Rockerball Arrive Installed and Torqued Down

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching