Replacement Buckle and Strap for Extang Trifecta 2.0

Question

Question:

To whom it may concern, Im inquiring about parts for my tonneau cover. I have a 2.0 and one of the clips to the straps broke, I would like to buy a new one and replace it! I would be thankful to let me know how I can purchase one. Thank you,

asked by: Jason S

1

Helpful Expert Reply:

Sounds like you have an Extang Trifecta 2.0 and are in need of a replacement male bucket and strap kit part # EX54440400.

expert reply by: Jameson C

1

Answer 1

To install the Replacement Male Buckle and Strap for Extang Trifecta and Trifecta Signature Tonneau Cover #EX54440400, you will need to gain access to one end of the center support beam that the male buckle straps slide on. The replacement straps…

view full answer...

Answer 2

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly…

view full answer...

Answer 3

view full answer...

Answer 4

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 5

I have exactly what you're looking for! You'll need the Replacement Tarp for Extang Trifecta 2.0 Soft Tonneau Cover #EX94770-20 to replace the tarp on your Extang Trifecta #EX94770 (Extang part #46770). This is the Extang Trifecta 2.0 Soft…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Buckle and Strap for Extang Trifecta 2.0

Product Page this Question was Asked From

Continue Researching