What Do You Have to Do To Install the Replacement Male Buckle Strap for an Extang Trifecta Cover

Question

Question:

how do I install

asked by: Rick

0

Expert Reply:

To install the Replacement Male Buckle and Strap for Extang Trifecta and Trifecta Signature Tonneau Cover # EX54440400, you will need to gain access to one end of the center support beam that the male buckle straps slide on. The replacement straps have a loop on them, this allows them to slide on the beam. You will slide the replacement strap(s) on and then reassemble the cover.

expert reply by: Scott S

0

Adam

3/22/2026

How do you "gain access"? Is there a video that can be shared?

Robin H.

4/27/2026

@Adam what you’re really doing is partially taking apart the end of the support bow (that center crossbar) so you can slide the new strap on. The straps aren’t bolted in, they ride along that bar, so you just need an open end to feed them on. Start by opening the cover and folding it up so you can clearly see the center support beam. At one end of that beam, there will be either a plastic end cap or a bracket that’s held in place with a screw or two. That’s your entry point. Remove that end cap or loosen the bracket just enough to free the end of the bar. You don’t have to completely disassemble the cover, just create enough space so the end of the beam is exposed. Once that end is open, take your replacement strap (the looped end is the key here) and slide it directly onto the beam. It should move along the bar just like the original one did. Position it roughly where the old strap sat.

Answer 1

Hey Patrick, the Replacement Male Buckle and Strap for Extang Trifecta and Trifecta Signature Tonneau Covers #EX54440400 is sold individually. If you needed two of these you'd need to order a quantity of two of them.

view full answer...

Answer 2

We do have the whole buckle assembly Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 If you need just the female end you want Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers #EX54560402 available as just the…

view full answer...

Answer 3

Sounds like you have an Extang Trifecta 2.0 and are in need of a replacement male bucket and strap kit part #EX54440400.

view full answer...

Answer 4

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 5

I have exactly what you're looking for! You'll need the Replacement Tarp for Extang Trifecta 2.0 Soft Tonneau Cover #EX94770-20 to replace the tarp on your Extang Trifecta #EX94770 (Extang part #46770). This is the Extang Trifecta 2.0 Soft…

view full answer...

Answer 6

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What Do You Have to Do To Install the Replacement Male Buckle Strap for an Extang Trifecta Cover

Product Page this Question was Asked From

Continue Researching