What Trailer Lift Kits Will Work with the MORryde CRE3000 Equalizers

Question

Question:

See thread below from a previous question. I have the Moryde 3000 equalizer and I see that the reccomended unit wont work. What are other options to correct this condition?

asked by: Bill

0

Expert Reply:

I do still have a few options for lifting the trailer but the Correct Track Trailer Alignment and Lift Kit part # RR23QX is indeed incompatible with the MORryde CRE3000 Equalizers. Therefore, you can either change these out to standard ones like the Curved Equalizer for 1-3/4" Wide Double-Eye Springs part # TREQE1 or look into an axle over conversion kit. That said, this option only works for you if the leaf springs are under the axle. If so, I recommend the Dexter Trailer Springs Over-Under Conversion Kit part # K71-384-00 for 2-3/8" or part # K71-385-00 for 3". This kit will lift the trailer around the sum of the axle and leaf spring pack thickness.

If you need a different size equalizer other than what's listed above you can check out our list below.

expert reply by: Conner L

0

Dimensions for Correct Track Adjustment Plate
(click to enlarge)

Brian

8/15/2024

I don’t think you answered his question. If we have the CRE3000, what kits ARE compatible?

Jon G.

8/15/2024

@Brian There aren't any standard lift kits like the Correct Track that work for your CRE3000. The solution, as Conner mentioned, is to use an over-under kit - part # K71-384-00 for 2-3/8" or part # K71-385-00 for 3".

Brian

8/15/2024

@JonG got it. My springs are already mounted on top of my axles. I have a 19’ Dutchmen Voltage towed by a 22’ F350 and I need more frame clearance between frame and bed rails while turning. It sounds like the easiest way is to get correct track and ditch the CRE3000 stabilizers for the equa-flex?

Jon G.

8/16/2024

@Brian Yes, you are correct. The only alternative to swapping out your equalizers is to have your current hanger brackets cut off and new ones welded on - which definitely isn't easier. If you let me know what CRE3000 kit you have I can let you know what the Equa-Flex alternative is!

See All (15) Replies to Brian ∨

Answer 1

Hi Greg; leaf springs aren't typically used to raise a trailer. However, if the #EM28AJ matches your current leaf spring measurements, and your current leaf springs are 3-leaf, and the leaf springs are sitting on top of the axle, that would push…

view full answer...

Answer 2

Hello Steve, thanks for reaching out. In my honest opinion, leaf springs are leaf springs. There is not going to be a noticeable difference in quality or longevity between the different brands. As long as the length of the spring is correct and the…

view full answer...

Answer 3

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 4

Yes, the Blue Ox Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BLU52XR is compatible with a Rota-Flex pin box but you'll need to use the Rota-Flex Lockout Kit #BLU62XR for that application. Attached are some review videos for you to check out!

view full answer...

Answer 5

The Trailair Rota-Flex 5th Wheel Pin Box - Lippert 1621 or 1621HD - 18,000 lbs #LC328330 does require capture plates for the Demco Hijacker autoslide that is similar to the Pull Rite Autoslide you have. The measurement from the front of the plate to…

view full answer...

Answer 6

The Rota-Flex Lockout Kit for Blue Ox 5th Wheel Hitches #BLU62XR is just a lockout kit to prevent the Rota-Flex head from pivoting, making it a standard pin box again so you shouldn't have a problem using it with your Andersen Hitch.

view full answer...

Answer 7

Hey Mark, I looked up the specs of the spring you have now and found that it is a 24-3/4 inch long spring from eye center to eye center and for a 7k axle. So that means that the replacement spring part #EM28AJ that you referenced will work great as a…

view full answer...

Answer 8

Hey Richard! How did you measure your current leaf springs to get the 25-1/2" eye to eye measurement? We recommend jacking one side of the trailer up to get the weight off of them before measuring because they stretch out quite a bit over years…

view full answer...

Answer 9

There are a couple of things that you can do to get more ground clearance for your new trailer. First, if the leaf spring stack is attached under the axle then you could use an over/under conversion kit. If the trailer has a 2-3/8 inch diameter round…

view full answer...

Answer 10

Hey Josh! If you have 8,000 lbs torsion axles I do not have a lift kit for you. I do have a couple of options for standard axles though. If your 8,000 lbs axles are mounted above your springs you can use the Dexter Trailer Springs Over-Under…

view full answer...

Answer 11

The Correct Track Tandem Lift kit part #RR23QX cannot work with the CRE3000 kit you have on your trailer now due to clearance issues so you would need to replace them with like with the EquaFlex part #LC145546 which is also cushioned.

view full answer...

Answer 12

Hello Loni. No, the Weight Distribution Shank for Gen-Y Hitch Adjustable Ball Mounts w/ 2-1/2" Receivers - 21K #GY98ER is not compatible because it has a 3/4" pin hole diameter, and the Fastway e2 requires a standard 5/8" pin hole…

view full answer...

What Trailer Lift Kits Will Work with the MORryde CRE3000 Equalizers

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching