How to Remove and Install the Top Mounting Clamp for Thule Ride-On Adapter

Question

Question:

How do I remove the old part and install the new part?

asked by: Michelle M

0

Expert Reply:

There will be 3 combinations of nuts and bolts that secure the Replacement Top Mounting Clamp for Thule Ride-On Adapter # 853-5267. Remove the nuts, then the bolts from your accessories and then simply reverse that process to install the replacement part.

expert reply by: Jon G

0

Bolt Holes for Replacement Top Mounting Clamp for Thule Ride-On Adapter
(click to enlarge)

Answer 1

To replace the mounting hardware that came with your Thule Atlantis 2100 roof cargo box you need the following parts: - Quick Grip Mount Assembly #TH05738 - Slide Strip #TH05401 - Snapfit Cradle Replacement Kit #TH68NB The Quick Grip and Slide Strip…

view full answer...

Answer 2

The flat side of the Replacement Cradle for Thule AcuTight and Quick Grip Mounting Hardware part #TH8523387001 will go against the bottom of the cargo box which you can see in the attached photo. Therefore, the screw hole will be facing down towards…

view full answer...

Answer 3

The Replacement Thule AcuTight Cradle #TH8523387001 is a single cradle while the Thule Snapfit Cradle Replacement Kit #TH68NB contains 4 cradles and 4 screws.

view full answer...

Answer 4

Hey Rob, thanks for reaching out! The Quick Grip Mount Assembly #TH05738 has a screw in the middle on the underside (see attached photo) that you can try removing to see if that lets you get inside to fix anything. I haven't done this on my end…

view full answer...

Answer 5

It would appear that the Replacement Top Mounting Clamp #853-5267 and Replacement Bottom Mounting Clamp #753-2854 are the correct brackets for your ski carrier. These brackets have a 4" on center bolt hole spread for attaching to the crossbars.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How to Remove and Install the Top Mounting Clamp for Thule Ride-On Adapter

Product Page this Question was Asked From

Continue Researching