Can I Replace Rear Panel on 2022 Cadillac XT4 with Draw-Tite Hitch Installed

Question

Question:

Can I put that back panel back in place if I have this hitch installed on my 2022 XT4?

asked by: Sherry

0

Expert Reply:

Yes, once the Draw-Tite Max-Frame Trailer Hitch Receiver # 76266 is installed on your 2022 Cadillac XT4 you'll be able to place that rear bumper fascia cover back over it for an OEM look.

I'm attaching an installation video and some photos for you to check out about this.

If you're planning on doing some towing with this hitch then I also recommend picking up the T-One Wiring # 118795, the Mount Bracket # 18144, and the Ball Mount Kit # C45154.

Attached are some additional videos for you to reference as well.

expert reply by: Jon G

0

Cover Off and Draw-Tite Hitch Installed on 2020 Cadillac XT4
(click to enlarge)

Cover On and Draw-Tite Hitch Installed on 2020 Cadillac XT4
(click to enlarge)

Answer 1

Good morning, Rich. I do have one resource which you should find helpful. I am sorry to say that at this time we do not have any pictures of videos of the Curt #C62ZV hitch being installed on a Cadillac Lyriq. Reason being we have not had this…

view full answer...

Answer 2

To tow a small trailer with the 2020 Cadillac XT4 you will need a hitch, wiring, ball mount and lock. For the hitch, I recommend Curt Trailer Hitch Receiver part #C39FR which is a concealed cross tube hitch so the only part of the hitch that is…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...