Replacement Motor Solution for Kwikee 59734-20

Question

Question:

Need a replacement motor for Coachsteps retractable steps on my motorhome. My motor p/n is 59734-20 and has a different 2-prong connector than what you show?

asked by: Mark B

0

Expert Reply:

The step motor 59734-20 will need to be replaced with the Replacement Motor for Lippert Electric Coach Step part # LC301695. If your connectors are different you could remove the connector on your current motor and install it in place of what comes with this motor so that it can install.

expert reply by: Jameson C

0

Answer 1

The correct replacement for your Klauber K01431B300 slide-out motor is the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511.

view full answer...

Answer 2

Yes, you can add a 7-way harness to the inside of your 2023 Ford F-150's truck bed. You will need the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector for Aluminum Beds item #C57008. This custom fit harness puts a 7-way…

view full answer...

Answer 3

To add a 7-way to your 2023 Ford F-150 that already has a 4-way, all you need is the following: - Universal Installation Kit for Trailer Brake Controller #ETBC7 This will give you the 7-way, wiring, circuit breakers, and rest of the hardware needed…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Motor Solution for Kwikee 59734-20

Product Page this Question was Asked From

Continue Researching