Replacement Roll Bar For a Solera 20' Long Awning

Question

Question:

I have a camper and the awning arms measure 20 foot center to center could you tell me want size roller bar I would need to order I think its item #LC89UD thank you.

asked by: David R

0

Expert Reply:

Yes, the Solera Rollbar # LC89UD will replace your roll bar with awning arms 20' across on center. This particular roll bar is gray in color. We also have it in Black # LC33FR if you need that color. Both will fit either manual or power awnings.

expert reply by: Bud M

0

Answer 1

When you go to install the Replacement Pitch Arm part #LC375994 you'd need to go with three of the retaining washers #LC431583.

view full answer...

Answer 2

Since you were looking at the Regal style idler head #LC672052 I'm assuming you need to replace the idler head pin on your Solera awning. You can remove the old pin and install #LC27WD for a replacement. If by key you mean a cotter pin, then yes…

view full answer...

Answer 3

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Roll Bar For a Solera 20' Long Awning

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching