How To Reset The Zero Point Calibration On A Lippert Ground Control 3.0 Leveling System
Updated 08/30/2022 | Published 08/29/2022
Question:
Trying to zero my unit back to a zero point.
asked by: David G
Expert Reply:
To recalibrate the Zero Point Calibration on your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590 you would need to complete the following steps listed below:
1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center of the trailer and leveling it both front to back and then side to side. (See “Basic Jack Operation” for instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3. With the touch pad off, press and release the “FRONT” button (Fig. 22G) five (5) times and then press and release the “REAR” button (Fig. 22J) five (5) times.
4. The touch pad will flash and beep and the display will read “ZERO POINT CALIBRATION ENTER to set, Power to Exit” (Fig. 33).
5. To set the current position as the zero point, press the “ENTER” button (Fig. 22C).
6. LCD display will read “Zero point stability check” (Fig. 34).
7. LCD display will read “Zero point set successfully” once process is complete (Fig. 35).
8. The system will set this point as its level state and the touch pad will turn off.
I have had people report that they've experienced issues with it calibrating correctly and the solution has been to slightly tilt the nose of the fifth wheel above level before beginning the calibration process.
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: kwikee step motor
- Search Results: motor for electric steps
- Search Results: rv steps motor
- Search Results: rv step motor
- Q&A: Fifth Wheel Hitch for 2017 Chevy Silverado 2500
- Search Results: husky hitch
- Search Results: trailer tongue jack
- Q&A: What SnapPads Fit a 2026 Keystone Montana Fifth Wheel?
- Search Results: 5th wheel slider hitch
- Shop: Fifth Wheel Hitch
- Shop: B&W Patriot 5th Wheel Trailer Hitch w/ Slider - Dual Jaw - 18,000 lbs
- Shop: RVpaws V2 Premium Articulating RV Jack Pads for 2" Square Jack Legs - 12" - Qty 2
- Shop: RVpaws V2 Premium Articulating RV Jack Pads for Equalizer 10" Square Legs - 9" - Qty 2
- Shop: RVpaws V2 Premium Articulating RV Jack Pads for Lippert Level Up and Titan Systems - 9" - Qty 2
- Shop: RV Jack Pads
- Shop: Replacement Motor for Kwikee Electric RV Steps - 12V
- Shop: Replacement Kwikee Electric Motor Assembly with 14NM IMGL RV Steps
- Q&A: Installation Process On B&W Patriot 5th Wheel Trailer Hitch w/ Slider
- Shop: BulletProof Hitches Weight Distribution System w/ Sway Control - No Shank - 14K GTW, 1.4K TW
- Shop: Tonneau Cover
- Q&A: How to Initially Adjust the Dexter Nev-R-Adjust Electric Trailer Brakes
- Q&A: Dexter Never Adjust Brakes Initial Adjustment on Tandem Axle Trialer
- Q&A: How to Reset Zero Point Calibration on Lippert Ground Control 3.0
- Video: Ultimate Overview of the Replacement 24-1/2" Right Rear Leg
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Camper Jacks
