Difference Between Grease Seal Numbers # RG06-070 And # GS-2250DL

Question

Question:

Wondering what the difference is between TruRyde bearings RG06-070 and GS-2250DL. Any difference in quality? They both seem to be 2.25 x 3.376. Thanks

asked by: Randy D

1

Helpful Expert Reply:

Both the TruRyde Seals GS-2250DL and RG06-070 have an inner diameter of 2.250 inches and an outer diameter of 3.376 inches and works with E-Z Lube End Units.

They are the same except one comes with 2 pieces when the other comes with 1.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

Hey Robert, welcome back! The Dexter 010-036-00, our item #RG06-070, and the Timken item #TMK58ZR are functionally the same grease seal. Timken is known for using higher quality materials in their parts so they do cost noticeably more. Both the item…

view full answer...

Answer 2

Essentially there is no difference between #RG06-070 and #GS-2250DL. Either would work well for the same applications. They are both double-lip grease seals with the same dimensions of 2.250 inch internal and 3.376 inch outside diameter.

view full answer...

Answer 3

Yes, the seals of part numbers #RG06-070 and #GS-2250DL are the exact same. Both have inner diameter of 2.25 inch and outer diameter of 3.376 inch and also are double lip seals.

view full answer...

Answer 4

The difference between the two part numbers you mentioned is the quantity of seals that comes with the part number. Part #RG06-070 is for a pair of seals whereas the part #GS-2250DL is for an individual seal.

view full answer...

Answer 5

You can use the Timken Grease and Oil Seal #TMK98ZR in place of the Grease Seal #GS-2250DL. While they are not exactly the same seal construction it is still a double lip design and the dimensions are the same so they are going to fit correctly.

view full answer...

Answer 6

If you take a look at the dimensional drawing of the Reese Goose Box #RP94720 I attached, you can see that it measures 18.56 inches from the middle of the bottom bolt hole and the bottom of the coupler where the ball connects, so not the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Difference Between Grease Seal Numbers # RG06-070 And # GS-2250DL

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching