Curt Shock Absorbing Towing Kit w/ Sway Control and without Wireless Brake Controller

Question

Question:

Can you buy this product without the wireless brake controller thanks

asked by: Bobby G

0

Expert Reply:

If you wanted to order the Curt Shock Absorbing Towing Starter Kit pat # C57DR without the brake controller you'd just need to order the individual components of the kit without the controller. So what you'd want would be the Rocker Ball # C45WR, the sway control part # 17200 and the Curt anti-rattle kit part # C22321.

expert reply by: Jameson C

0

Answer 1

I would be happy to help you. We hear this complaint quite often about dealerships not wanting to install after market wiring for random reasons because they want you to purchase theirs usually. The Curt Shock Absorbing Towing Kit w/ Sway Control and…

view full answer...

Answer 2

Yes, the Primus IQ Brake Controller part #TK90160 will install the exact same as the following instructions: According to my research, the 2016 Colorado/Canyon with the factory 7-way won't have a plug under the dash for installing a brake…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Donny; after looking at several videos of the trailer it does appear to have a 6 on 5-1/2 bolt pattern with ST225/75R15 tires. The Goodyear Endurance ST225/75R15 Radial Tire w/ 15" Eagle Aluminum Wheel #GY97QB will be a direct fit.

view full answer...

Answer 12

Hi Frank, While we can get you a brake controller for your 2020 Chevy Colorado, there isn't a plug-in option and harness because the truck doesn't have a plug under the dash. That said, the wires are already run to the cab, so it isn't…

view full answer...

Curt Shock Absorbing Towing Kit w/ Sway Control and without Wireless Brake Controller

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching