Lift Kit for 2015 Rockwood Signature Ultra Lite 8280WS 5th Wheel

Question

Question:

Can you tell me if i can use a lift on a 2015 rockwood signature ultra light w8380 fifth wheel? I am pulling with a ram 2500 and would like it to sit more level. The front is to high. It does have torsion susp2

asked by: Dean L

0

Expert Reply:

The correct lift kit for a Dexter 4,000 Lb Torsion Axle is the Torflex Lift Kit part # K71-707-02 which provides a 2-5/8" lift.

expert reply by: Conner L

0

Answer 1

Hello Jay, welcome back. No, the Curt Custom Fifth Wheel Installation Kit #C38ZV will not fit the 2024 Ford F-150 Lightning. I don't think a lot of people are towing with these electric trucks, at least not enough to justify any of our…

view full answer...

Answer 2

Thank you for providing that picture and helpful information. The correct lift kit for a 3,000 lb Dexter #10 torsion axle like yours is the #K71-707-01. This comes with all of the necessary hardware and will give you a 2-5/8" lift.

view full answer...

Answer 3

We may have a solution available for you though we do not have a list of individual parts for specific trailers. However, you will likely find something that works, such as the Global Link RV Entry Door Locking Latch Kit #295-000019, which is a…

view full answer...

Answer 4

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter - 20,000 lbs #AM3200 does give you a 9 inch offset but when talking with their tech he said that to use with RamBox the red coupler needs to be turned 180 degrees so it sits…

view full answer...

Answer 5

While we do not have a video on how to replace the strut assist on your MORryde StepAbove RV Steps #MR28RR, I would be happy to walk you through it. Before we begin, you'll want to follow the below preparation steps: Step 1: Remove the step’s…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Lift Kit for 2015 Rockwood Signature Ultra Lite 8280WS 5th Wheel

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching