Tow Ready Trailer Ball Torque Rating and Socket for Installing

Question

Question:

Hello, can you tell me how tight the nut for the hitch ball should be on a ball mount? Right now I have it on as tight as I could get it with a large crescent wrench. My auto mechanic could probably torque it down for me if I knew the correct rating. Thanks in advance.

asked by: Justin P

0

Expert Reply:

The Tow Ready 2 Inch Hitch Ball, item # 63845, you have referenced needs to be torqued to 250 foot pounds. It is recommended to frequently check that the ball is tightened to these specifications.

I recommend using the 1-7/8" 12pt Thin Walled Socket - 3/4" Drive - Chromium-Vanadium Steel item # ALL643216 to install it.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 9

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Answer 10

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 11

Hey Jon, I have a solution for you but I would not recommend the Andersen Weight Distribution system part #AN33VR for your 2025 Brinkley Z Air 297. What we have found is that the Andersen system does a decent job with lighter weight trailers but for…

view full answer...

Answer 12

-Hey Tom, Equal-i-zer makes frame brackets for 8 inch trailer frames. For that you would need the part #EQ90-02-5378 for outer link and then for an inner link part #EQ90-02-5208. You'd need two of these with the system you order since the…

view full answer...

Tow Ready Trailer Ball Torque Rating and Socket for Installing

Products Featured in This Question

Continue Researching