Will Rhino Rack Conduit Clamp Fit Top Channel of Thule Load Bars

Question

Question:

Will these fit the slot on Thule load bars

asked by: Rex E

1

Helpful Expert Reply:

Yes, the Conduit Clamp Set for Rhino-Rack Heavy-Duty Crossbars part # RRBC2 will fit the top channels of your Thule load bars.

expert reply by: Jameson C

1

Answer 1

I suppose you could drill a hole into your conduit carrier, and use the Replacement Square Head Bolt for Thule Fairings #853-208909 with a M6 nut to secure the conduit carrier to your Thule AeroBlade Edge Roof Rack. Or You could use the Conduit Clamp…

view full answer...

Answer 2

The Thule WingBars, like part #TH711200 have a top opening of 1/2 inch and a 3/4 inch width at the bottom.

view full answer...

Answer 3

The Conduit Clamp Set for Rhino-Rack Heavy-Duty Crossbars part #RRBC2 is designed for the Rhino Rack Heavy Duty Crossbars. The Rhino Rack Vortex Pipe Clamps for Conduit Carriers part #RRSPC4 are designed for Rhino Rack Vortex Aero Crossbars. The two…

view full answer...

Answer 4

The Conduit Clamp Set #RRBC2 that you referenced is designed specifically to mount to the C-channels that are present on Rhino-Rack Heavy Duty Crossbars. These particular model bars feature a unique C-channel that differs from the standard opening on…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Will Rhino Rack Conduit Clamp Fit Top Channel of Thule Load Bars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching