Does the Buyers Products Ladder Rack # BP69FR Fit a 2017 Toyota Tundra with 5-1/2 Foot Bed?

Question

Question:

Will this ladder rack for on a 2017 Toyota Tundra crew max 5’ 6” bed

asked by: Chad L

0

Expert Reply:

The Buyers Products Over-The-Cab Truck Bed Ladder Rack # BP69FR fits your 2017 Toyota Tundra Crew Max with a 5-1/2 foot bed but only if you do not have Deck Rails installed on your truck's bed. While we have different racks that are compatible if you have Deck Rails, we do not have any models of the Buyers Products rack that fit.

With that being said, if you have Deck Rails on your Tundra, I recommend the Thule TracRac SR Sliding Truck Bed Ladder Rack - 1,250 lbs # TH97RV. This rack has a similar weight capacity as the # BP69FR (1,250 pounds). It also includes rails that allow you to fully adjust the bases anywhere on the rails of your bed. It involves a no-drill installation and is 100% made in the U.S.A.

expert reply by: Bob C

0

Answer 1

Hello Greg, We have a sliding option for you, but I am very sorry they do not make the rack you were looking at for your 2016 Toyota Tundra 5'6" bed. The best sliding option that we have for you would be the Thule Xsporter Pro Shift Overland…

view full answer...

Answer 2

Since your 2016 Toyota Tundra has the 5-1/2' bed and the deck rail system you are going to want the Thule TracRac SR Sliding Truck Bed Ladder Rack item #TH97RV. For the cab extension you will need the Cantilever Extension item #TH24001XT. There…

view full answer...

Answer 3

Hello Joe, Thanks for writing in! Based on the measurements you provided, the Gen-Y Glyder Shock Absorbing Ball Mount #325-GH-12001 is not the right fit for your setup. Since your Tundra's receiver measures 18 inches from the ground and your TAB…

view full answer...

Answer 4

Hey Joe. To connect the Parkit360 Force Electric Trailer Dolly item #PA46VR to your trailer's battery, you'll need the Bulldog Winch Front Wiring Kit item #BDW20025. The Bulldog Winch Front Wiring Kit item #BDW20025 has the same style…

view full answer...

Answer 5

Hi Grant, Thanks for the photo—and that's a nice boat! Based on what you've described, I do think adding a weight distribution system would be a great upgrade to your towing setup, especially for longer trips where you'll also be carrying…

view full answer...

Answer 6

Hey Lloyd! I'm not able to get you the exact height the etrailer Over-The-Cab Ladder Rack #e78FV is going to sit above your F-350's cab only because this rack fits a lot of different truck configurations and we haven't been able to take…

view full answer...

Answer 7

Hey Craig, thanks for reaching out! I believe the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK will work as replacements for your 2008 Featherlite 4926 trailer, but you'll need to confirm this on your end. These lights carry the…

view full answer...

Answer 8

I spoke with Buyers Products about the Buyers Products Over-The-Cab Truck Bed Ladder Rack w/ Rear Window Guard #BP69FR they stated the space between the uprights is approximately 73". There are welded on tie-down brackets that stick out…

view full answer...

Answer 9

Bearing Buddy bearing protector grease caps are made in many sizes and we carry those most often used in recreational trailering. You can see all Bearing Buddy parts we have by clicking on the page I linked for you. Bearing Buddy grease caps are made…

view full answer...

Answer 10

The downside to buying a "bargain" trailer kit is that customer support, both in terms of helpful information and available replacement parts, can be scarce. The other issue is that products made to sell at a tempting price point may not…

view full answer...

Answer 11

For a replacement hub that uses #L44643 bearings with a 5 on 4.5 bolt pattern you'll want the Dexter Trailer Idler Hub Assembly #8-258BTUC1. This will come as a quantity of one so you'd need two kits to do both sides of the axles. Each kit…

view full answer...

Answer 12

The Dexter hub you referenced, 8-201, is a 5,200 lb hub, though a 5 on 4-1/2 bolt pattern does not come on 5,200 lb hubs. The correct bearings for the 5,200 lb hub are #25580 and #LM67048, while the proper races are #25520 and #LM67010. I have…

view full answer...