Diameter Of The Rear View Safety Monitor Mount Ball

Question

Question:

can you tell me please what size ball is being used to fit inside the arms and base .. it appears to be 1inch .. similar to a Ram size 1inch ball .. ?

asked by: Glenn S

0

Expert Reply:

I went out to our warehouse and measured the ball of the Rear View Safety Monitor Mount # RVS-1420 and found it to be 7/8" in diameter.

expert reply by: Kevin C

0

Answer 1

Yes, you can upgrade the 4.3 inch monitor of your Furrion setup to the 7 inch #FR47FR or the #FR97FR for the 5 inch. This will work great and give you an easy to view monitor.

view full answer...

Answer 2

The distance between the screw holes on the Rear View Safety Monitor Mount #RVS-1420 are as follows: Vertical: 2" center of hole to center of hole Horizontal: 2" center of hole to center of hole Diagonal: 2-3/4" center of hole to…

view full answer...

Answer 3

I checked with Furrion and the 7 inch and 5 inch monitor version of the Furrion observation system #FOS05TASF use part #FR79SR. The smaller 4.3 inch size use the part #LC776462. The ball of the #FR79SR is 0.85" or 21.59mm and the ball of the…

view full answer...

Answer 4

The angle of the Furrion side marker cameras in the kit part #FCE48TASL isn't adjustable. It's set at an angle that when you have it installed on the front of the trailer you'll see a small portion of the trailer and as wide of an angle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Diameter Of The Rear View Safety Monitor Mount Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching