Replacement Fulton Jack For A 2002 Boston Whaler EZLoader Trailer

Question

Question:

Can you tell me which Fulton jack would be a good replacement for the 800lb bolt-on Fulton jack on my 2002 Boston Whaler EZLoader trailer? Not sure of travel since it is totally apart, but the top tube is 15.5x2, bottom tube is 13.5x1.75.

asked by: Mark O

1

Helpful Expert Reply:

When it comes to replacing your 800 pound bolt Fulton Jack on your 2002 Boston Whaler The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10 inch Lift - 1,200 pounds # FTJ12000101 will work. This bolt on jack fits up to 3 inch by 5 inch trailer tongues.

The jack has a 10 inch lift and has a lift capacity of 1,200 pounds. The jack is made out a heavy-gauge steel that has a 600-hour salt spray rating. It has a 11 inch clearance from the mounting bracket to the top of the jack.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

Yes, you can install a trailer jack on your EZ loader boat trailer with an aluminum 3" x 5" I-beam frame. However, you will want to use a bolt-on jack like the Fulton Round, Snap-Ring Swivel Marine Jack part #FTJ12000101 as a weld-on jack…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 7

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Answer 8

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 9

Hey Will! The square tube on the Bigfoot Hydraulic Trailer Jack #BF94FR is 4" x 4". What kind of trailer do you have?

view full answer...

Answer 10

It sure does Steve! Our 3,500 lbs etrailer Electric Trailer Jack w/ Tongue Weight Scale item #e43KV also comes in a 5,000 lbs capacity. We have two different options depending on how you want to power it that I have listed below: Wired to Trailer -…

view full answer...

Replacement Fulton Jack For A 2002 Boston Whaler EZLoader Trailer

Featured Help Information

Miscellaneous Media

Continue Researching