Front Air Bag Suspension Kit that Fits 2003 Workhorse RV Chassis

Question

Question:

I want to put air bags on 2003 workhorse front I beam suspension .is there a kit that will work.i can fabricate if necessary

asked by: Robert D

0

Expert Reply:

If your 2003 Workhorse RV is a P series P30 or P32 or the W18 series you'd want the Air Lift # AL81560.

expert reply by: Jameson C

0

Answer 1

For front air bags that fit inside of the coil springs on your 2002 Workhorse P32 chassis you will need #AL81560. You can roll up these bags and insert them up from the bottom through the hole below the coil spring mounts that you have described. No…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 7

Hi Todd, I know exactly the feeling you’re describing, and you’re definitely not alone. That floaty, pushy feeling at highway speeds, especially when trucks pass, is really common on the Sprinter 3500 chassis with a taller coach like your Tiburon,…

view full answer...

Answer 8

Hey Josh! Yes, the Pacbrake Alpha XD Pro Air Bag Suspension Kit w/ Internal Jounce Bumpers #PB89RV will fit your Sprinter. This is specifically designed for models with dual rear wheels. The only reason these wouldn't work is if you have the ride…

view full answer...

Answer 9

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 10

Hey Jeff, I would strongly recommend the SumoSpring kit part #SS96EV for your 2025 Nissan Frontier. This will give you the support you are looking for without causing the ride quality to be overly harsh which the Timbrens are known to do. Install is…

view full answer...

Answer 11

Hey Don, thanks for reaching out. Yeah, the driver’s side on those F53 chassis can get tight, you’ve usually got brake lines, wiring, or a bracket sitting right where you want that Timbren to live. You’re doing the right thing paying attention to it,…

view full answer...

Answer 12

Hey Shawn. The 1-1/8" Diameter Hellwig Sway Bar item #HE73GR is going to reuse the factory end links on your 2014 Ram 2500 and is designed as a simple replacement for the stock sway bar. I recommend installing the thicker 1-1/4" Diameter…

view full answer...

Front Air Bag Suspension Kit that Fits 2003 Workhorse RV Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching