Lead And Follow Leg Repair Kit For A Lippert Venture Landing Gear VMC900R-327953

Question

Question:

Can you give me the correct parts for this jacks,both of them?

asked by: Wayne N

0

Expert Reply:

For your lead jack leg on your Lippert Venture Landing Gear VMC900R-327953, you will want to use the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059.

As for a follow leg kit, you will want to use the Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear # LC146060.

Attached are a couple of review videos for you to check out.

expert reply by: Bryce D

0

Answer 1

I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the…

view full answer...

Answer 2

Essentially the two jack legs are the same and either would work. Since the price is better the one I would go with is the part #LG-179013 which is the 29-1/2 inch length that you need.

view full answer...

Answer 3

You could use the Landing Gear part #RVLG-8HDL as a replacement for what you have now on our 2011 Wildcat by Forest River. This will bolt right up in place of what you have and has plenty of capacity at 8,000 lbs so it will operate easily.

view full answer...

Answer 4

The landing gear looks like a standard set based on the pictures and the dimensions you listed. The part #LC146060 would be what you need for the follow leg and then part #LC146059 for the lead leg.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Lead And Follow Leg Repair Kit For A Lippert Venture Landing Gear VMC900R-327953

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching