How Does Lasalle Crossbreeze Toy Hauler Screen Install

Question

Question:

I have the moreryde patio kit installed on my Attitude 2414BSG and it is bolted to the inside of my trailer so it takes up a few inches into the trailer. Will the crossbreeze still work? Does it screw into the side walls and the roof or does it screw into the roof and the door frame?

asked by: Daniel S

0

Expert Reply:

The install of the LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen # 3441409775PBK consists of cutting the rails to the correct length to match door height, inserting the header into the rails and then using included screws to attach rails to wall on either side of door opening. It installs on the inside of the toy hauler. It shouldn't be an issue with the inflatable patio set you have currently.

expert reply by: Jameson C

0

Carl

10/4/2024

do you have a video for installation ? thx

Jameson C.

10/6/2024

@Carl We do not have a video since we do not carry that anymore.

Answer 1

If it is necessary to cut the rails, I suggest you place the top piece into the side rails and measure from the top to the point that matches your desired length. Please look at image number 2 and compare to your particular camper. Can you place the…

view full answer...

Answer 2

Yes, the MORryde StepAbove RV Steps with Strut Assist like #MR85RR can use the removable mounting plate. It isn't compatible with the struts but you already plan to remove them so that won't be an issue. Assuming you have a 26-28" wide…

view full answer...

Answer 3

The Furrion 34" Electric Fireplace w/ Wood #FF34SW15ABL requires a rough opening/cutout that measures 30-9/16 inches wide, 16-1/4 inches tall, and 5 inches deep. I have attached a short video review that you can check out as well.

view full answer...

Answer 4

I reached out to the manufacturer, LaSalle Bristol, who told me the width measurement is the housing of the screen, so it is the entire unit. They did say the screens are between 1/8" and 1/4" narrower than the size says to account for…

view full answer...

Answer 5

If you can measure the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK is the correct screen if your opening is 97-3/4 inches wide. If you need a…

view full answer...

Answer 6

Yes, the LaSalle Bristol CrossBreeze Screen, #3441409775PBK is attached to the inside wall of your toy hauler. The inside-wall-to-inside-wall measurement is what is crucial for fitment. For your RV, you provided a measurement of 98-1/2" so the…

view full answer...

Answer 7

If you measure just the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK that you referenced is the correct screen if your opening is 97-3/4 inches wide.…

view full answer...

Answer 8

The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screens do not use magnets to stay down. You simply need to pull the lanyard and you can actually stop it at any point of its length and it will automatically stop due to a mechanism in the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

How Does Lasalle Crossbreeze Toy Hauler Screen Install

Product Page this Question was Asked From

Continue Researching