LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen For 2010 Keystone Fuzion TT Toy Hauler

Question

Question:

I have a 2010 Keystone Fuzion Touring Edition II. The measurement of rear opening width = 93 13/16, height = 88 1/8. And I realize the screen doesnt mount inside this opening, because that would reduce the opening for loading toys. The measurement between inside walls width = 98 1/2 to 5/8-. The height floor to ceiling = 98 1/2. From the descriptions, it sounds like the assembly is screwed into the side walls, just inside the rear metal door frame. I also have a power up/down ram for the rear ramp, and cables that should be on the outside of this screen, if I understand the mounting described. I can disconnect the ram after the ramp is down and supported by the cables so we have a deck or just down on the ground as a ramp. I took photos, so if you need some let me know. Is it possible to take the 99 1/8inch model apart and reduce the width to exactly the width I need? Or use the 97 3/4inch model and provide some spacers and foam to fill the small gap between the screen frame and the toy-hauler walls, to keep the critters out.

asked by: Jim P

0

Expert Reply:

Yes, the LaSalle Bristol CrossBreeze Screen, # 3441409775PBK is attached to the inside wall of your toy hauler. The inside-wall-to-inside-wall measurement is what is crucial for fitment. For your RV, you provided a measurement of 98-1/2" so the 97-3/4" wide, # 3441409775PBK is what you will need.

There is not an option to disassemble and cut width for fitment.

When installing, you will need to fit within the walls of your RV and build-up the gap by using spacers, running a strip of lumber from floor to ceiling, something to bring the mounting point of the inside-wall-to-inside-wall into proper spec. You are looking at gap of 3/4" total. You may decide to split this, building each side up to close that gap or, mount off-center and only need to build up on the one side. With your 93-13/16" doorway, you may decide you have enough overlap.

The canister that this rolls into is 3" diameter. If you have bunks mounted to a rail that move up/down within your garage, you will need to consider that clearance.

expert reply by: Michael R

0

Answer 1

If it is necessary to cut the rails, I suggest you place the top piece into the side rails and measure from the top to the point that matches your desired length. Please look at image number 2 and compare to your particular camper. Can you place the…

view full answer...

Answer 2

The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screens do not use magnets to stay down. You simply need to pull the lanyard and you can actually stop it at any point of its length and it will automatically stop due to a mechanism in the…

view full answer...

Answer 3

If you can measure the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK is the correct screen if your opening is 97-3/4 inches wide. If you need a…

view full answer...

Answer 4

If you measure just the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK that you referenced is the correct screen if your opening is 97-3/4 inches wide.…

view full answer...

Answer 5

The install of the LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen #3441409775PBK consists of cutting the rails to the correct length to match door height, inserting the header into the rails and then using included screws to attach rails to…

view full answer...

Answer 6

I reached out to the manufacturer, LaSalle Bristol, who told me the width measurement is the housing of the screen, so it is the entire unit. They did say the screens are between 1/8" and 1/4" narrower than the size says to account for…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

Hey Nick, thanks for reaching out. Yes, the Replacement Fabric for etrailer Powered RV Awnings #e96QV will work with other brands of awning like Solera or Dometic which are what we commonly see on campers like your 2011 Forest River Cherokee 29U. The…

view full answer...

Answer 11

Hey Lee! The Victron parts can get pretty confusing. The Victron Orion-Tr #VN75ZR is only designed to be a power supply for DC loads, not for battery charging. You do not want to use this converter to charge any type of battery. To charge your…

view full answer...

LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen For 2010 Keystone Fuzion TT Toy Hauler

Product Page this Question was Asked From

Continue Researching