Recommended Replacement Velcro Strips For A Tonno Pro Lo-Roll Tonneau Cover

Question

Question:

Apparently Replacement Velcro for Tonno Pro Lo-Roll Tonno Covers # TPLR-VELCRO us no longer available. Do you sell an equivalent that would work? Im looking specifically for the hook side.

asked by: Lars K

1

Helpful Expert Reply:

Since the Velcro strip in your Tonno Pro tonneau cover is 1-1/4" wide you could slide it out and use the Replacement Adhesive Velcro Strip for Access Tonneau Covers # A20790. This strip has an adhesive backing to help secure it to the railing of your cover.

expert reply by: Kevin C

1

Answer 1

We have replacement tonneau cover Velcro that is exactly 1-5/16 inches wide with the Truxedo part #TX1115174 which would fit your rails. It can be cut down shorter too as it is 80 inches long.

view full answer...

Answer 2

I have a solution for you, and the strips that you're referring to are going to come in a couple different sizes, but none of them are going to be 1-1/16" wide. The #TX1117876 strips you're referring to are 1" wide, which have the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Recommended Replacement Velcro Strips For A Tonno Pro Lo-Roll Tonneau Cover

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching