Which Wheel Caster Can be Used with Ultimate Trailer Jack # 322-RDJ-2K

Question

Question:

I read the JC-102 was recommended for this jack, but I need one with slightly greater capacity. Will this one work? Replacement Heavy-Duty, 6inch Caster for 2inch Diameter Bulldog Jacks - 1,500 lbs Item # BDCP555

asked by: Christopher S

0

Expert Reply:

We can't recommend the use of the Bulldog wheel caster with the Ultimate Trailer Jack # 322-RDJ-2K. The only one that can be used is the # JC-102 which is a confirmed fit.

expert reply by: Jameson C

0

Answer 1

The distance from the center of the hitch pin hole to the gusset welded onto the Curt #C45311 is 4 inches, as shown in the provided photo. If you're wanting something with a longer shank for additional clearance, I'd recommend the Curt…

view full answer...

Answer 2

Hi Robert, So there isn't one that can be used with a cordless drill (which would be an electric jack only) as all the electric A-frame jacks are all higher than the 12" to 14" you want. There is a manual crank jack you can use which I…

view full answer...

Answer 3

I went out to the warehouse and found that the distance from the center of the jack to the furthest part of the adjustment pin on the Ultimate Trailer Jack #322-RDJ-2K when it is pulled out is 5-3/8". If you have this much room from the center…

view full answer...

Answer 4

The Ultimate Trailer Jack #322-RDJ-2K is our only A-Frame mounted tongue jack that we currently carry that will has a height of less than 9" above the trailer tongue. This jack has 7 height settings allowing for up to 12" of lift and will…

view full answer...

Answer 5

Yes, the Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs #322-RDJ-2K you were looking at can be removed from the mounting bracket by removing the keeper pointed out in the included diagram, and then removing the foot. After…

view full answer...

Answer 6

The main difference between a ST205/75-14 size tire like the Contender #AC14R45SM and a ST215/75-14 size tire like the Taskmaster Provider Item #TTWTR21514 is that the larger number is a slightly larger size. The 205 has a section width of 7.99"…

view full answer...

Answer 7

I recommend the Bulldog Round, Pipe-Mount Swivel Jack #BD1541150301 to replace the Fulton jack currently on your trailer. The Bulldog jack uses the same Pipe Mount connection so that you can easily replace your jack. The jack is rated for 2,000lbs…

view full answer...

Answer 8

The item you selected, Bulldog Jack, Sidewind Swivel - 2,000 lbs, part #BD1541150301, requires the use of a pipe mount to be welded to the frame of your trailer. I contacted our representative at Bulldog, and he informed me that to mount part…

view full answer...

Answer 9

I have a replacement jack option for you, but I do not recommend cutting off the footplate and drilling a hole in the tube to mount a caster like the Removable 6" Caster for 2-1/4" Trailer Jacks - Steel Caster - 1,200 lbs Item #JC-102 to…

view full answer...

Answer 10

The Bulldog Pipe Mount Jack part #BD1541150301 would work well for you. This jack is a pipe mount like you would need and has the ability to install a wheel like part #BD500245 or a foot plate like part #BD018564. You should note that with the wheel…

view full answer...

Answer 11

The Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 2,000 lbs #PS1401060303 has an overall length when retracted of 16-5/8 inches. This jack does not have a wheel. For a similar jack with a wheel, I recommend the…

view full answer...

Answer 12

I went out into our warehouse and pulled a Bulldog Round, Pipe-Mount Swivel Jack, part #BD178203, that has the same 2 inch inner diameter and 2.5 inch outer diameter pipe mount swivel jack as yours. I then test fit a Bulldog 2-1/2 inch Long, Weld-On…

view full answer...

Which Wheel Caster Can be Used with Ultimate Trailer Jack # 322-RDJ-2K

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching